Troy-Bilt E686NHorseTM, 682JHorseTM, E682LHorseTM manual Maintenance and Storage, Operating Symbols

Page 5

Section 1: Safety

Maintenance and Storage

1.Keep the tiller, attachments and acces- sories in safe working condition.

2.Check all nuts, bolts, and screws at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

3.Never store the tiller with fuel in the fuel tank inside a building where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc.). Allow engine to cool before storing in any enclosure.

4.To reduce the chances of a fire hazard, keep the engine free of grass, leaves, or excessive grease.

5.Store gasoline in a cool, well-ventilated area, safely away from any spark- or flame-producing equipment. Store gasoline in an approved container, safely away from the reach of children.

6.Refer to the Maintenance sections of this Manual and the separate Engine Owner’s Manual for instructions if the tiller is to be stored for an extended period.

7.Never perform maintenance while the engine is running or the spark plug wire is connected, except when specifically instructed to do so.

8.If the fuel tank has to be drained, do this outdoors.

Decals

For your safety and the safety of others, various safety and operational decals are located on your unit (Figure 1).

Keep the decals clean and legible at all times. Contact your local service dealer or the Factory for replacements if any decals are damaged or missing.

Refer to the Parts List for decal locations, descriptions and part numbers.

A) WARNING: Hot Surfaces.

C) WARNING: Operating and

Safety Instructions

Top of the air cleaner housing.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E) Forward

D) Power Unit

 

Interlock

 

Operating

 

Lever (2)

 

Instructions

 

 

F) Engine Stabilization.

B) WARNING: Engine Ignition.

 

Top of fuel tank.

Electric start models only.

 

Figure 1: Location of Safety and Operating Decals. (Briggs & Stratton engine shown)

Operating Symbols

Various symbols (shown here, with word

descriptions) are used on the tiller and engine. FAST Your unit may not have all of the symbols.

 

STOP

 

 

 

SLOW

STOP

CHOKE

CHOKE

ROTATING

 

ON

OFF

 

 

TINES

 

 

 

 

WARNING

TO AVOID SERIOUS INJURY:

READ THE OWNER’S MANUAL.

KNOW LOCATIONS AND FUNCTIONS OF ALL CONTROLS.

KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING.

NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER.

SHUT OFF ENGINE AND DISCONNECT SPARK PLUG WIRE BEFORE MANUALLY UNCLOG- GING TINES OR MAKING REPAIRS.

KEEP BYSTANDERS AWAY FROM MACHINE.

KEEP AWAY FROM ROTATING PARTS.

USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU.

5

Image 5
Contents Operator’s Manual Table of Contents Safety Alert Symbol SafetyUse slower wheel, tine and engine speeds SafetyKeep children and pets away Operating Symbols Maintenance and StorageIntroduction Tools/Materials Needed for AssemblyInspect Unit Attach HandlebarMove Tiller Off Shipping Platform AssemblyRemove the temporary screw J, Figure Check Gear Oil LevelsAttach Engine Throttle Lever and Cable Adjust Air Pressure in TiresAdd Motor Oil to Engine Oil Level HoleConnect the Wire Harness Receptacle Install Battery CablesTo Avoid Personal Injury or Property Damage Never bring a gas can near the positiveWheels/Tines/PTO Drive Lever PTO Attachments FeatureForward Interlock Levers EngineHandlebar Height Adjustment Lever Features and ControlsWheel Speed Lever Tines/PTO Clutch LeverMove the engine Throttle lever to Stop position Keyswitch StarterEngine Controls Engine Throttle Lever Pre-Start Checklist Following steps describe how to start and stop the engineBreak-In Operation Starting and Stopping the EngineMove engine throttle lever -2 away from Stop OperationOperating the Tiller Cold Weather OperationStopping the Engine and Tiller Moving the Tiller Forward and TillingStopping Reverse Motion Moving the Tiller in ReverseTo Stop the Engine Making TurnsHow to Check the Interlock System Testing the Forward Interlock Safety SystemLoading and Unloading the Tiller Transporting The Tiller Around Your PropertyLoading the Tiller Changing Speed BeltsUnloading the Tiller Changing Belt From LOW Range to High RangeChanging Belt From High Range to LOW Range Choosing Wheel Tine SpeedsMove the Wheels/Tines/PTO Drive Lever into Neutral Go to right side of tiller and finish seating the beltTilling depths Let the tiller do the workAvoid tilling wet, soggy soil To help avoid personal injury, be awareSuggested tilling patterns Avoid making footprintsTilling on slopes Tilling up and down slopesTerrace Gardening Clearing the tinesSoil Enrichment Idea Wide-Row PlantingTilling Under Corn Removing Tine Attachment Removing And Replacing The Tine AttachmentMove the tiller to level ground Place Wheel Speed Lever into Free Wheel FigureSetting Up Stationary Attachments Installing the Tine AttachmentGuide Pin Mounting Hole Move the two swing-bolts intoStarting The Engine Setting Up Non-Powered Attach- mentsOperating Stationary Attachments Stopping the EngineHours EveryTiller Lubrication MaintenanceTighten Bolts and Nuts Checking the Power Unit Oil Level Transmission Gear Oil MaintenanceChecking for Oil Leaks Checking Gear Oil LevelsChecking the Tine Attachment Oil Level Adding or Changing Gear OilFor Dipsticks With Hot/Cold Markings If the level is incorrect, see Adding or Changing Gear OilDraining and Filling PTO Power Unit Transmission Adding Gear Oil to PTO Power Unit TransmissionAdding Gear Oil to the Tine Attachment Transmission Draining and Filling the Tine Attachment TransmissionMeasuring and Adjusting Drive Belt Tension Drive Belt MaintenanceHow to Measure Belt Tension Belt Adjustment ToolReplacing the Drive Belt Replacing the Drive BeltRemoving the Belt Reverse Disc Inspection Reverse Drive System MaintenanceInstalling a New Reverse Disc Checking and Adjusting Reverse the Drive SystemChecking and Adjusting Reverse Disc Replacing the Reverse DiscChecking Tines for Wear Bolo Tine MaintenanceAdjusting Reverse Drive Removing and Replacing a Tine Holder Assembly Single Tine ReplacementRemoving Tine Holder Assembly Replacing Tines Holder AssemblyTire and Wheel Maintenance Tine Shaft MaintenanceAir Cleaner Maintenance Spark Plug MaintenanceStoring Your Tiller Inspecting Forward Interlock Wiring SystemTesting the Forward Interlock Wiring System Troubleshooting Procedures Appendix a TroubleshootingLinkage EccentricTiller Pulls To One Side 290-258-081 290-257-081 Row Marker AttachmentDozer/Snow Blade Attachment Wrap-Around Bumper GuardPage Page TROY-BILT Tiller Lifetime Limited Warranty

E682LHorseTM, E686NHorseTM, 682JHorseTM specifications

Troy-Bilt is a recognized leader in outdoor power equipment, particularly known for its innovative and reliable garden tillers. Among its extensive lineup, the Troy-Bilt 682J Horse™, E686N Horse™, and E682L Horse™ tillers stand out for their robust performance and advanced technological features. Each model is uniquely designed to cater to different gardening needs, making them essential tools for both novice and experienced gardeners.

The Troy-Bilt 682J Horse™ is a commercial-grade tiller that boasts a powerful 6 HP engine, providing ample torque for breaking new ground or cultivating soil. Its 12-inch steel tines are designed for durability and efficiency, allowing for effective tilling at a depth of up to 8 inches. The unique counter-rotating tine feature enhances soil mixing and reduces the risk of soil compaction, ensuring optimal planting conditions. Additionally, the rear-wheel drive system offers superior traction and maneuverability, making it easier to navigate through tough terrain.

Next in line, the E686N Horse™ brings a slightly different set of capabilities, with an emphasis on user comfort and ease of operation. This model is equipped with a powerful 6.5 HP engine, which allows for efficient handling of larger plots. Its forward and reverse gear options provide flexibility in operations, especially when navigating tight spaces. The adjustable tilling width allows users to choose between 16 and 12 inches, making it versatile for various gardening tasks. This model also features an ergonomic design that includes adjustable handlebars, making it easier for users of different heights to operate comfortably.

Finally, the E682L Horse™ is designed for lighter gardening tasks. With a more compact design, this tiller features a 5 HP engine that delivers reliable performance for small to medium gardens. Its tilling depth of up to 6 inches and width of 18 inches makes it ideal for homeowners looking to maintain their garden beds or small plots. The E682L Horse™ incorporates a lightweight and easy-to-maneuver body, allowing for effortless transportation and storage.

All three tillers leverage advanced technologies such as Troy-Bilt's patented Walk Behind design, which provides optimal control and reduces fatigue during extended use. The durability of the construction materials ensures longevity, while user-friendly features enhance the overall gardening experience. Whether you are a professional landscaper or a homeowner with a passion for gardening, the Troy-Bilt 682J Horse™, E686N Horse™, and E682L Horse™ offer tailored solutions that meet a wide array of tilling needs.