Land Pride RTR0542, RTR0550 manual Driveline Shortening

Page 16

Table of Contents

Section 1: Assembly and Set-Up

Land Pride

23758

Driveline Shortening

Figure 1-12

Refer to Figure 1-1on page 10:

IMPORTANT: The implement must be raised fully up when checking to see if the driveline will fit correctly between tractor and tiller.

1.Start tractor and slowly engage tractor’s hydraulic 3-point to lift the arms fully up.

2.Slide the slip clutch or shear bolt yoke end of driveline (#9) over the splined input shaft of gearbox (#3). Secure with driveline yoke locking device.

3.Slide the opposite driveline yoke end over the tractor’s splined driveline shaft. Secure with driveline yoke locking device. Skip to step 5 if driveline fits between tractor and implement.

Refer to Figure 1-12:

4.The driveline will require shortening if it is too long. Shorten driveline as follows:

a.Set tractor in park, shut tractor engine off, set park brake and remove switch key.

b.Pull driveline apart into two sections as shown in Figure 1-12.Attach the outer driveline universal joint to the tractor shaft and inner driveline universal joint to the tiller gearbox shaft. Pull on each driveline section to be sure the universal joints are secured to the shafts.

c.Hold the driveline sections parallel to each other to determine if they are too long. The inner and outer shields on each section should end approximately 1/4" short of reaching the universal joint shield on the adjacent section

(see “B” dimension). If they are too long, measure 1/4" (“B” dimension) back from the universal joint shield and make a mark at this location on the inner and outer driveline shields.

d.Cut off the inner shield at the mark (“X” dimension). Cut the same amount off the inner shaft (“X1” dimension). Repeat cut off procedure (“Y” & “Y1” dimensions) to the outer driveline half.

e.Remove all burrs and cuttings.

f.Apply multi-purpose grease to the inside of the outer shaft and reassemble the driveline.

g.Attach inner driveline yoke end to the tiller divider gearbox input shaft.

h.Attach outer driveline yoke to the tractor's shaft.

5.The driveline should now be moved back and forth to insure that both ends are secured to the tractor and tiller shafts. Reattach any end that is loose.

IMPORTANT: Two small chains are supplied with the driveline. These chains must be attached to the driveline shields and to the rotary tiller and tractor to restrict the shields from rotating.

6.Hook driveline safety chain at the tiller to the square tube located between the two hitch plates. Re-latch safety chain at the driveline guard.

7.Hook driveline safety chain at the tractor to the tractor. Re-latch safety chain at the driveline guard.

8.Slowly operate the tractor's 3-point hydraulic control up and down and check for clearance between the driveline and drawbar.

14 RTR0542 and RTR0550 Rotary Tillers 311-464M

8/27/08

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Rotary Tillers Table of Contents Important Safety Information Be Aware Signal WordsFor Your Protection Shutdown and StoragePractice Safe Maintenance Use Safety Lights and DevicesTransport Machinery Safely Wear Protective Equipment Prepare for EmergenciesAvoid High Pressure Fluids Hazard Reference RTR0542 & RTR0550 Shown 818-171CReference RTR0542 Shown & RTR0550 818-142C 818-284CReference RTR0542 Reference RTR0550818-543C 818-552C818-130C 818-540C Reference RTR0542 & RTR0550Using This Manual ApplicationOwner Assistance IntroductionDealer Preparations Assembly and Set-UpTractor Requirements Support Stand Adjustment Hitch AssemblyPoint Category 0 Hitch Tractor Hook-UpPoint Category I-Limited Hitch Point Category I Hitch Support Stand StoragePoint Hitch Checks Point Category I Quick HitchDriveline Installation Refer to -10& FigureDriveline Shortening General Notes for Field Operations Operator’s ResponsibilitiesOperating Transporting Operating Check ListParking General Operating Instructions Point Hitch Adjustment Drive Chain Tension AdjustmentRear Deflector Adjustment Skid Shoe AdjustmentMaintenance Tine ReplacementMaintenance and Lubrication Clutch Run-InClutch Disassembly Clutch AssemblyStorage InspectionLubrication HrsBearing On Right End Of Rotor Shaft GearboxRTR05 Series Specifications & CapacitiesModel RTR0542 RTR0550 Features and Benefits Features BenefitsTroubleshooting Problem Cause SolutionAppendix Torque Values Chart for Common Bolt SizesIn-tpi1 Ft-lb3 · m · m ft-lb Overall Unit and Driveline One year Parts and Labor WarrantyTines and Driveline Friction Discs Considered wear items Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

RTR0550, RTR0542 specifications

Land Pride RTR0542 and RTR0550 are leading models in the realm of rotary tillers, designed to cater to the needs of both agricultural professionals and avid gardeners. With their robust construction and advanced features, these tillers provide efficient soil preparation and cultivation for a variety of applications.

The RTR0542 and RTR0550 models come equipped with high-quality, heat-treated tines that enhance durability and longevity. These tines are engineered for maximum soil penetration and effective tilling, ensuring that the soil is thoroughly mixed and aerated. With a tilling width of 42 inches for the RTR0542 and 50 inches for the RTR0550, these tillers allow users to cover larger areas in less time, making them highly efficient for both large-scale farming and home gardening projects.

One of the standout features of both models is their adjustable side skids. These allow operators to customize the depth of the tilling process, adapting to different soil conditions or planting requirements. This flexibility is essential for optimal seedbed preparation, making the rotary tillers suitable for a wide range of crops, from vegetables to flowers.

The RTR0542 and RTR0550 are built with a sturdy, heavy-duty frame that ensures stability and alignment during operation. This robust construction not only enhances performance but also minimizes wear and tear, further extending the lifespan of the equipment. Additionally, the tillers come with a shielded chain drive system that reduces noise and maintenance needs, offering operators a quieter and more efficient working experience.

Both models feature a quick-hitch compatibility, allowing for easy and efficient attachment to a range of tractors. This convenient design enables users to switch between implements without the need for extensive equipment changes, enhancing productivity and versatility on the farm or in the garden.

Safety is also a priority in the design of RTR0542 and RTR0550. They are equipped with safety shields that protect operators from flying debris while working. The inclusion of durable bearings helps to reduce vibrations, ensuring a smoother operation and improved user comfort.

In summary, Land Pride RTR0542 and RTR0550 rotary tillers offer an impressive combination of durability, efficiency, and versatility. With their advanced features and technologies, these tillers are ideal for anyone looking to achieve superior soil preparation and cultivation for successful planting and gardening endeavors. Whether you are a commercial farmer or a backyard gardener, these models can meet diverse soil management needs effectively.
Top Page Image Contents