Land Pride RTR0550, RTR0542 manual General Operating Instructions

Page 19

Land Pride

Section 2: Operating

Table of Contents

General Operating Instructions

Before using your Land Pride RTR05 Series Reverse-Tine Rotary Tiller, you should have completely read the Operator’s Manual, properly attached the Tiller to the tractor, cut the driveline to proper length, run-in the clutch if your model is equipped with one, and gone through the Operating Checklist. If you have missed any of these steps, please complete them before proceeding.

Now that you have properly prepared yourself and your tiller, it’s time to do some tilling. Carefully drive the tractor to the site where you intend to till. You should have already cleaned this site of any large limbs, rocks, trash, metal or extraneous debris. If you are in tall grass or weeds, we highly recommend you cut or mow before you till.

Line the tractor up just to the right of center on your tillage plot. You will be working from the center out and turning to the left to line up for your next pass. Lower the tiller half way to the ground and reduce your tractor engine speed to idle. Engage the PTO and gradually increase the engine speed until you reach full PTO speed of 540 rpm. Lower the tiller to the ground and simultaneously commence forward travel as ground conditions warrant. Do not make turns or attempt to back up while tiller is in the ground. See important note below.

IMPORTANT: Turning or backing up with rotary tines in the ground will damage the tiller.

Travel about 50 ft. and then stop to check your results. When stopping, remember to lift the tiller out of the ground, stop the tractor, reduce engine speed, disengage the PTO, set the park brake, shut off the tractor, and remove the keys. If you are tilling too shallow or too deep, adjust the skid shoes accordingly. If the soil texture is too coarse, lower the leveling door and reduce your ground speed. If the soil texture is too fine, you will need to raise your leveling door and increase your ground speed. For any other problem conditions that may arise, you will want to refer to the Troubleshooting section on page 25.

When you are done tilling for the day, make sure you use proper tractor shut down procedures before you get off of the tractor. If you are detaching your tiller, make sure you park it on a dry and level surface leaving it clean and ready for the next use. When you put your tiller up for the season, make sure you refer to the Storage Directions on page 20.

With a little practice and a few adjustments, you will soon be achieving the results you want with your Land Pride 05 Series Reverse Tine Rotary Tiller. See “Features and Benefits” on page 24 or “Product Specifications” on page 23 for additional information and performance enhancing options.

8/27/08

RTR0542 and RTR0550 Rotary Tillers 311-464M

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Rotary Tillers Table of Contents Shutdown and Storage Important Safety InformationBe Aware Signal Words For Your ProtectionPractice Safe Maintenance Use Safety Lights and DevicesTransport Machinery Safely Wear Protective Equipment Prepare for EmergenciesAvoid High Pressure Fluids Hazard Reference RTR0542 & RTR0550 Shown 818-171CReference RTR0542 Shown & RTR0550 Reference RTR0550 818-142C818-284C Reference RTR0542818-543C 818-552C818-130C Reference RTR0542 & RTR0550 818-540CIntroduction Using This ManualApplication Owner AssistanceDealer Preparations Assembly and Set-UpTractor Requirements Hitch Assembly Support Stand AdjustmentPoint Category 0 Hitch Tractor Hook-UpPoint Category I-Limited Hitch Point Category I Quick Hitch Point Category I HitchSupport Stand Storage Point Hitch ChecksRefer to -10& Figure Driveline InstallationDriveline Shortening General Notes for Field Operations Operator’s ResponsibilitiesOperating Transporting Operating Check ListParking General Operating Instructions Skid Shoe Adjustment Point Hitch AdjustmentDrive Chain Tension Adjustment Rear Deflector AdjustmentClutch Run-In MaintenanceTine Replacement Maintenance and LubricationInspection Clutch DisassemblyClutch Assembly StorageHrs LubricationGearbox Bearing On Right End Of Rotor ShaftRTR05 Series Specifications & CapacitiesModel RTR0542 RTR0550 Features Benefits Features and BenefitsProblem Cause Solution TroubleshootingAppendix Torque Values Chart for Common Bolt SizesIn-tpi1 Ft-lb3 · m · m ft-lb Overall Unit and Driveline One year Parts and Labor WarrantyTines and Driveline Friction Discs Considered wear items Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

RTR0550, RTR0542 specifications

Land Pride RTR0542 and RTR0550 are leading models in the realm of rotary tillers, designed to cater to the needs of both agricultural professionals and avid gardeners. With their robust construction and advanced features, these tillers provide efficient soil preparation and cultivation for a variety of applications.

The RTR0542 and RTR0550 models come equipped with high-quality, heat-treated tines that enhance durability and longevity. These tines are engineered for maximum soil penetration and effective tilling, ensuring that the soil is thoroughly mixed and aerated. With a tilling width of 42 inches for the RTR0542 and 50 inches for the RTR0550, these tillers allow users to cover larger areas in less time, making them highly efficient for both large-scale farming and home gardening projects.

One of the standout features of both models is their adjustable side skids. These allow operators to customize the depth of the tilling process, adapting to different soil conditions or planting requirements. This flexibility is essential for optimal seedbed preparation, making the rotary tillers suitable for a wide range of crops, from vegetables to flowers.

The RTR0542 and RTR0550 are built with a sturdy, heavy-duty frame that ensures stability and alignment during operation. This robust construction not only enhances performance but also minimizes wear and tear, further extending the lifespan of the equipment. Additionally, the tillers come with a shielded chain drive system that reduces noise and maintenance needs, offering operators a quieter and more efficient working experience.

Both models feature a quick-hitch compatibility, allowing for easy and efficient attachment to a range of tractors. This convenient design enables users to switch between implements without the need for extensive equipment changes, enhancing productivity and versatility on the farm or in the garden.

Safety is also a priority in the design of RTR0542 and RTR0550. They are equipped with safety shields that protect operators from flying debris while working. The inclusion of durable bearings helps to reduce vibrations, ensuring a smoother operation and improved user comfort.

In summary, Land Pride RTR0542 and RTR0550 rotary tillers offer an impressive combination of durability, efficiency, and versatility. With their advanced features and technologies, these tillers are ideal for anyone looking to achieve superior soil preparation and cultivation for successful planting and gardening endeavors. Whether you are a commercial farmer or a backyard gardener, these models can meet diverse soil management needs effectively.
Top Page Image Contents