Land Pride RTR0542 Point Hitch Adjustment, Drive Chain Tension Adjustment, Skid Shoe Adjustment

Page 20

Table of Contents

Section 3: Adjustments

3-Point Hitch Adjustment

1.Park tractor and tiller on a flat level surface.

2.Slowly raise the tiller with the tractor’s hydraulic

3-point lift until the tines are about 1-2” above the ground.

3.Ensure that the lower arms are blocked to prevent excessive side movement.

4.Place a spirt level on the top cover running from left to right and adjust one of the lower 3-point arms up or down until the tiller is level from left to right.

5.Rotate the spirt level 90 degrees and adjust the tractor’s top center link in or out until the tiller is level from front to back.

6.Slowly operate the tractor's 3-point hydraulic control up and down to check for clearance between the tires, frame, drawbar etc.

Drive Chain Tension Adjustment

The tension on the drive chain is self adjusting and does not require any maintenance during the life of the chain.

Rear Deflector Adjustment

Refer to Figure 3-4:

The rear deflector (#1) can be adjusted closer to the ground to produce a fine soil texture or can be raised to produce a coarse soil texture. Adjust the chain length by repositioning the chain (#2) in slot “A”.

23778

Rear Deflector

Figure 3-4

Skid Shoe Adjustment

Refer to Figure 3-5:

The skid shoes can be adjusted to the desired tilling depth by raising or lowering them as follows:

1.Raise tiller off the ground. Place a support under the tiller times (not under the skid shoes) and lower the tiller onto the support. Make certain the tiller is secure when resting on the support before working on or around the tiller.

2.Always place tractor in park, set tractor brakes, shut tractor engine off and remove switch key before dismounting the tractor.

3.Loosen 1/2” -13 nut (#5).

4.Remove 1/2” nut (#3), 1/2” lockwasher (#4) and 1/2”- 13 x 1 1/4” GR5 hex head cap screw (#2).

5.Pivot skid shoe down or up to the desired height and replace hex head cap screw (#2). Secure cap screw with nut (#3) and lockwasher (#4).

6.Tighten nuts (#3 & #5) to the correct torque. Refer to Torque Values Chart in the “Appendix” section on page 26 for the proper torque.

IMPORTANT: Be sure both skid shoes are adjusted the same.

23781

Skid Shoe Adjustment

Figure 3-5

18 RTR0542 and RTR0550 Rotary Tillers 311-464M

8/27/08

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Rotary Tillers Table of Contents Important Safety Information Be Aware Signal WordsFor Your Protection Shutdown and StorageTransport Machinery Safely Use Safety Lights and DevicesPractice Safe Maintenance Avoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Reference RTR0542 Shown & RTR0550 818-171CReference RTR0542 & RTR0550 Shown 818-142C 818-284CReference RTR0542 Reference RTR0550818-130C 818-552C818-543C 818-540C Reference RTR0542 & RTR0550Using This Manual ApplicationOwner Assistance IntroductionTractor Requirements Assembly and Set-UpDealer Preparations Support Stand Adjustment Hitch AssemblyPoint Category I-Limited Hitch Tractor Hook-UpPoint Category 0 Hitch Point Category I Hitch Support Stand StoragePoint Hitch Checks Point Category I Quick HitchDriveline Installation Refer to -10& FigureDriveline Shortening Operating Operator’s ResponsibilitiesGeneral Notes for Field Operations Parking Operating Check ListTransporting General Operating Instructions Point Hitch Adjustment Drive Chain Tension AdjustmentRear Deflector Adjustment Skid Shoe AdjustmentMaintenance Tine ReplacementMaintenance and Lubrication Clutch Run-InClutch Disassembly Clutch AssemblyStorage InspectionLubrication HrsBearing On Right End Of Rotor Shaft GearboxModel RTR0542 RTR0550 Specifications & CapacitiesRTR05 Series Features and Benefits Features BenefitsTroubleshooting Problem Cause SolutionIn-tpi1 Ft-lb3 · m · m ft-lb Torque Values Chart for Common Bolt SizesAppendix Tines and Driveline Friction Discs Considered wear items WarrantyOverall Unit and Driveline One year Parts and Labor Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

RTR0550, RTR0542 specifications

Land Pride RTR0542 and RTR0550 are leading models in the realm of rotary tillers, designed to cater to the needs of both agricultural professionals and avid gardeners. With their robust construction and advanced features, these tillers provide efficient soil preparation and cultivation for a variety of applications.

The RTR0542 and RTR0550 models come equipped with high-quality, heat-treated tines that enhance durability and longevity. These tines are engineered for maximum soil penetration and effective tilling, ensuring that the soil is thoroughly mixed and aerated. With a tilling width of 42 inches for the RTR0542 and 50 inches for the RTR0550, these tillers allow users to cover larger areas in less time, making them highly efficient for both large-scale farming and home gardening projects.

One of the standout features of both models is their adjustable side skids. These allow operators to customize the depth of the tilling process, adapting to different soil conditions or planting requirements. This flexibility is essential for optimal seedbed preparation, making the rotary tillers suitable for a wide range of crops, from vegetables to flowers.

The RTR0542 and RTR0550 are built with a sturdy, heavy-duty frame that ensures stability and alignment during operation. This robust construction not only enhances performance but also minimizes wear and tear, further extending the lifespan of the equipment. Additionally, the tillers come with a shielded chain drive system that reduces noise and maintenance needs, offering operators a quieter and more efficient working experience.

Both models feature a quick-hitch compatibility, allowing for easy and efficient attachment to a range of tractors. This convenient design enables users to switch between implements without the need for extensive equipment changes, enhancing productivity and versatility on the farm or in the garden.

Safety is also a priority in the design of RTR0542 and RTR0550. They are equipped with safety shields that protect operators from flying debris while working. The inclusion of durable bearings helps to reduce vibrations, ensuring a smoother operation and improved user comfort.

In summary, Land Pride RTR0542 and RTR0550 rotary tillers offer an impressive combination of durability, efficiency, and versatility. With their advanced features and technologies, these tillers are ideal for anyone looking to achieve superior soil preparation and cultivation for successful planting and gardening endeavors. Whether you are a commercial farmer or a backyard gardener, these models can meet diverse soil management needs effectively.
Top Page Image Contents