Husqvarna HUV 4213-GXP owner manual Battery

Page 39

Battery

2.Access the engine compartment. See WARNING “For vehicles with cargo beds...” in General Warnings on page 9.

3.Tilt the bed and ensure that the prop rod is properly engaged.

4.Disconnect the battery cables, negative (–) cable first. See WARNING “To avoid unintentionally starting...” in

General Warnings on page 9.

5.Use a flat blade screwdriver, and carefully remove the battery cell caps from the battery (Figure 25). See following WARNING.

WARNING

•Wear safety glasses or approved eye protection when servicing the vehicle. Wear a full face shield and rubber gloves when working on or near batteries.

6.Carefully check the electrolyte level and add distilled water if necessary. Do not fill above designated fill line. Replace battery cell caps.

7.Clean both battery terminals with a solution of baking soda and water (1 cup (237 mL) baking soda per gallon (3.8 L) of water). Rinse thoroughly. Do not allow this solution to enter the battery. Tighten battery terminals to 144 in-lb (16 N·m). Let the terminals dry and then spray them with Battery Terminal Protector Spray (P/N 603 00 00-03). See following CAUTION.

WARNING

•If battery wire terminals are damaged or corroded, replace or clean them as necessary. Failure to do so may cause them to overheat during operation and could result in fire, property damage, or personal injury.

1. Level Indicator 2. Cap 3. Plates

Electrolyte level at least 1/2 inch (13 MM) above plates or to level indicator.

180

22

Figure 25 Battery

Figure 26 Battery Electrolyte Level

Be sure battery hold-down clamp is properly tightened. Tighten to 144 in-Ib (16 N·m). A loose clamp may allow the battery to become damaged from vibration or jarring.

If battery appears weak, have it charged by a trained technician. The battery should never be left discharged any longer than absolutely necessary (do not leave discharged overnight).

2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual

Page 37

Page 38 Page 40
Image 39
Page 38 Page 40
Contents HUV 4213-G and HUV 4213-GXP Page Page Foreword Regular Maintenance Items Periodic Maintenance ItemsTable of Contents Safety Decal and Feature Identification HUV 4213-G/4213-GXP HUV 4213-G/4213-GXP Proposition 65 State of California Practice SafetySafety Details General Warnings General WarningsModel Identification Serial Number Controls and IndicatorsFORWARD/REVERSE Control KEY SwitchForward/Reverse Handle Accelerator PedalChoke Brake PedalPark Brake Lockout CAMLOW OIL Warning Light Differential LockLight BAR Control Seat Latch and AdjustmentFuel GAUGE/HOUR Meter Headlight ControlPerformance Inspection PRE-OPERATION and Daily Safety ChecklistDriving Instructions Driving InstructionsStarting the Vehicle Parking and Leaving the Vehicle Stopping the VehicleFront Shock Absorbers BED Latch and Prop RODLoading and Unloading Transporting on a Trailer Towing with the VehiclePreparing the Vehicle for Extended Storage StorageGeneral Warnings on Returning the Stored Vehicle to ServiceMaintenance MaintenancePeriodic Service Schedule Periodic Service Schedule Regular Interval Semiannually by owner or Periodic Lubrication ScheduleBrake Fluid Master CylinderEngine OIL Engine OIL Level CheckEngine OIL and Filter Change Engine Oil Drain Plug and Pan Compress Snubber Downward Coat Rubber Seal OIL ViscosityExtended Storage on Fueling InstructionsFuel Tank BatteryBattery Cleaning the Vehicle AccessoriesElectric Winch Accessory Subsequent Owner Registration Specifications HUV4213-GXP Vehicle SpecificationsLiquid Capacities Warranties WarrantyHOW to Make a Warranty Claim Your Warranty Rights and Obligations California Emission Control Warranty StatementItems Covered by this Warranty Husqvarna Forest & Garden Page Page Page 103372939
Top Page Image Contents