Generac QT04524ANSX UNDER-FREQUENCY Shutdown Alarm, Missing Crank Pulse Alarm, LOW Battery Alarm

Page 18

Control Panel

Figure 1 – Generator Control Panel

UNDER-FREQUENCY SHUTDOWN ALARM

After starting, if the generator stays under frequency for more than 30 seconds, it will shutdown.

MISSING CRANK PULSE ALARM

This is a shutdown alarm. The alarm will activate after 12 con- secutive revs where crank pulses are missing.

LOW BATTERY ALARM

While running if the average battery voltage falls below 11.9 volts for one (1) minute, the low battery alarm will be displayed.

LOW FUEL PRESSURE WARNING

Fuel pressure is monitored by a digital sensor with a fixed setpoint of below five (5) inches water column.

LOW BATTERY WARNING

The microprocessor will continually monitor the battery voltage and display the Low Battery Voltage message if the battery voltage falls below 12.2 Volts for one (1) minute.

No other action is taken on a low battery warning condition. The warning will automatically clear if the battery voltage rises above 12.2 volts.

NOTE:

The battery sentinel is a separate feature that monitors battery condition.

LOW COOLANT LEVEL ALARM

This is a shutdown alarm. The sensor will be continuously moni- tored. If an error condition is seen for five (5) consecutive sec- onds, the alarm will be displayed.

GOVERNOR SENSOR FAULT ALARM

The governor position is monitored by an analog feedback signal. If the throttle position is seen outside of the normal operating range, a shutdown alarm is displayed. If the throttle is commanded to move, and no movement is seen, a shutdown alarm is displayed.

WIRING ERROR ALARM

When power is first apllied to the contoller, the software will per- form a check on the wiring of the transfer output, and ensure it does not have high voltage on the wire. If this is the case, it will signal a miswire alarm and will not run. The test can be skipped by use of the escape key.

UNDERVOLTAGE ALARM

If the generator voltage falls below 60% for >5 seconds, an alarm will be issued.

MISSING CAM PULSE ALARM

This is a shutdown alarm. The alarm will activate after five (5) seconds of continuously missing cam pulses.

8-5

05/10 A .Rev CntrlNex001

Image 18
Contents Stationary Emergency Generator Table of Contents Introduction Operation and MaintenanceHOW to Obtain Service Read this Manual ThoroughlySafety Rules General HazardsFire Hazards Identification Record Data LabelEquipment Description Engine OIL RecommendationsCoolant Recommendations Engine Protective Devices Natural GAS Fuel System Fuel SystemFuel Requirements Propane Vapor Withdrawal Fuel SystemEngine SpecificationsStationary Emergency Generator Cooling SystemReconfiguring the Fuel System Weather and Maintenance KitsControl Panel Phase Alternators Y Configuration Alternator Power Winding ConnectionsFOUR-LEAD, SINGLE-PHASE Stator Alternator AC Lead ConnectionsStator Power Winding Connections 3-phase, 120/208V 6 Lead Activate the Generator Using the AUTO/OFF/MANUAL SwitchControl Panel Interface Display Interface MenusActivation Chart Choose Language TroubleshootingFuel Conversion Setting the Exercise TimerUser Adjustable Settings OperationAlarm and Warning Messages Auto StartManual Start LOW Battery Alarm UNDER-FREQUENCY Shutdown AlarmMissing Crank Pulse Alarm LOW Battery WarningCommon Alarm Relay Maintenance AlertsMenu System Stationary Emergency Generator Control and Operation Operating Unit with Manual Transfer SwitchOperating Unit with Automatic Transfer Switch Engine START-UP and TransferChanging Engine OIL General MaintenanceCheck Engine OIL Cooling INTAKE/OUTLETOverload Protection for Engine DC Electrical System Engine CoolantCoolant Change Exercise SystemBattery Fluid Battery MaintenanceBattery Replacement Spark PlugsService Schedule System / Component Frequency ProcedureTroubleshooting Guide Problem Cause CorrectionWarranty Purchaser’s/Owner’s Recordkeeping Responsibilities Page Page Assy STR 390 25GD3 CPL Page Group a UL Circuit Breaker 225AF Page UL Circuit Breaker KG Page UL Circuit Breaker QN This page Left Intentionally Blank Page Weldment Frame 2.4L C2 Page Battery Tray C1 CPL Page Gasket Bosch 32 Page Weldment Radiator Support C2 Page Page Group D Harn Emissions Overlay 2.4L not Shown Page Group E Page Exhaust Elbow 2 1/4 OD 2 1/2OD Page Rear Wrap C2 CPL Page Page Page Page Page Page Page Page Page Page Page Page Page Page 04/07 a .Rev BackPg001