Baldor PC1700RI, PC1100R manual Maintenance

Page 9

Warning Statements Continued

Maintenance

WARNING: Before cleaning, inspecting, repairing, refueling or performing any maintenance to the generator set, always be sure the engine has stopped and that all rotating parts have also stopped. After stopping, certain components are still extremely hot so be careful not to get burned.

WARNING: Before servicing the generator set, be sure to disconnect the spark plug wires to prevent accidental engine rotation or starting.

WARNING: Inspect all wiring frequently and replace any damaged, broken or frayed wiring or wires with damaged insulation immediately. Electrical shock can cause serious or fatal injury.

WARNING: Disconnect all electrical wires and load devices from generator power outlets before servicing the generator. Electrical shock can cause serious or fatal injury. Always treat electrical circuits as if they are energized.

WARNING: Check fuel tank, fuel line, and connections monthly for fuel leaks. Gasoline is flammable and can cause fire, explosions, injury or death. If a leak is found, replace only with approved pipe or components.

WARNING: Never store an engine with fuel in its tank indoors or in an enclosed, poorly ventilated area where gasoline fumes could reach an ignition source and cause an explosion.

Caution Statements

Caution: The brass connecting tab on some 120VAC duplex receptacles have been removed. Each receptacle is powered by a separate generator winding. When replacing a receptacle, inspect the brass tab that normally links both receptacles. If it is removed, be sure to remove the brass tab from the replacement receptacle before it is installed. Failure to remove the tab will cause a direct short to the generator windings and cause possible generator damage.

Caution: Avoid installing the generator set beside heat generating equipment, or directly below water or steam pipes or in the vicinity of corrosive substances or vapors, metal particles and dust. Heat can cause engine problems to develop and unwanted substances can cause rust or generator failure over time.

Caution: Do not apply high voltage to windings (start the generator) in a moisture−saturated condition. Moisture can cause insulation breakdown, making it necessary to return the generator to the factory for repair, and consequent expense and loss of time.

Caution: Use only original equipment or authorized replacement parts. Using the correct parts will assure continued safe operation as designed.

Caution: Do not suspend the generator from the top handle during operation.

Caution: Do not tamper with or change the engine speed. Engine speed is factory set to produce the correct voltage and output frequency.

Caution: Never operate the engine without a muffler and spark arrestor. The engine is designed to have the correct exhaust components installed. Operating without these components can present a fire hazard, cause excessive exhaust gases and cause damage to engine.

Caution: Operate the generator only on a level surface. Operation of the generator on an incline or slope may degrade engine lubrication and result in engine failure.

Caution: Always fill fuel tank with clean fresh fuel before use. Never leave fuel in tank for long storage periods. Old fuel becomes stale and can damage the fuel system causing the engine not to start. Always drain the fuel tank after use before storage.

Caution: For electric start models, do not place the key switch in the start position when engine is running. This causes the starting motor to engage and may damage the starter and engine.

MN2411

Product Safety Information 1-5

Page 8 Page 10
Image 9
Page 8 Page 10
Contents PC1100R/PC1700RI Portable Generator California Proposition 65 Warning Table of Contents Ii Table of Contents MN2411 Read This Manual Thoroughly Section Product Safety InformationOperation SymbolsOperation Warning Statements Burn Installation Maintenance Product Safety Information MN2411 Section General Information Limited WarrantyParts Generator Series LaborGeneral Information MN2411 Storage Section Receiving & InstallationPhysical Location Frame Ground Connection Engine Oil Frame Ground ConnectionUse of Electric Motor Loads Section Operation AC Circuit Breaker Operator Control Panel ~ AC OutputDC Circuit Breaker DC OutputOperator Control Panel DC Circuit Breaker Engine Switch StopRun ChokeOperation MN2411 Check Air Cleaner Left side cover Section Troubleshooting and MaintenanceCheck Fuel Level Check Oil Level SE or higher grade SAE 10W−30 or SAE 10W−40Clean Spark Arrester Clean/Adjust Spark Plug Right side coverCleaning Periodic Maintenance ScheduleTroubleshooting Guide Problems and SolutionsEngine Oil SE or higher grade SAE 10W−30 or SAE 10W−40 ServiceBaldor District Offices California Proposition 65 Warning

PC1700RI, PC1100R specifications

The Baldor PC1100R and PC1700RI are advanced servo motors that stand out in the competitive landscape of industrial automation. These motors are engineered to deliver exceptional performance characterized by high efficiency, reliability, and precision, making them ideal for a variety of applications ranging from robotics to CNC machinery.

The Baldor PC1100R model features a compact design that offers ease of integration into existing systems. With a power rating of 1.1 kW, it delivers robust torque performance while maintaining energy efficiency. This servo motor is equipped with high-resolution encoders that provide precise feedback for accurate position and speed control. The PC1100R also incorporates advanced thermal management technologies to ensure optimal operating temperatures, reducing the risk of overheating and prolonging the motor's lifespan.

On the other hand, the PC1700RI model offers increased power capacity, rated at 1.7 kW. This motor caters to more demanding applications, providing higher torque outputs without compromising on speed and responsiveness. The PC1700RI is designed with a modular architecture, allowing for versatile configurations that can be tailored to specific project needs. Both motors utilize integrated digital controls that enable seamless communication with various automation systems, facilitating smooth operation and enhanced flexibility.

In terms of construction, both the PC1100R and PC1700RI feature durable housing designed to withstand harsh industrial environments. They possess an IP65 rating, making them resistant to dust and water, which is essential for machinery operating in challenging conditions. Additionally, these motors are designed with low vibration and noise levels, contributing to a more comfortable working environment.

Another notable characteristic of the Baldor PC series is the ability to support a variety of feedback devices, including incremental and absolute encoders. This flexibility ensures compatibility with diverse applications and setups. Both models also come with comprehensive support and documentation from Baldor, ensuring users can efficiently implement and maintain their systems.

In summary, the Baldor PC1100R and PC1700RI servo motors exemplify top-tier engineering in the realm of industrial motors. Their features, including compact designs, high efficiency, advanced feedback systems, and robust construction, make them ideal for tackling the demands of modern manufacturing and automation processes. With their reliability and performance, these motors are poised to play a critical role in enhancing productivity across various industries.
Top Page Image Contents