Baldor AE11, AE10, AE25, AE8 manual Secure the Generator, Physical Dimensions

Page 16

Indoor Location Continued

4.Keep all fuel and its associated piping away from all components of the engine exhaust system.

5.The exhaust system should be inspected on a regular basis to assure there are no toxic exhaust gas leaks. In some areas this inspection may be provided by your local public service.

6.A carbon monoxide tester may be installed to detect the presence of the deadly gas during times when you are in the building with the engine running (during testing or maintenance).

Installation

The generator is completely assembled, tested and adjusted at the factory before it is shipped to

 

you. The procedures presented in this manual are suggestions and it is the responsibility of the

 

Owner/Operator to arrange for these procedures to be performed by licensed contractors

 

according to all applicable codes including local codes for your Municipality/City/County and

 

State. Installation generally includes the following:

1. Secure Generator to concrete pad.

2. Connect Fuel Supply.

3. Electrical Connections − power wiring (optional transfer switch) and control wiring.

4. Battery (not included).

5. Ground Connection.

After installation, the post installation checks must be performed prior to starting the engine. After these checks have been performed and the system operation is verified to be good, refer to Section 6 Maintenance for periodic checks that must be performed at scheduled intervals to ensure continued operation with minimal problems.

Secure the Generator

Refer to Table 3-1for the dimensions and weight of each generator. Mounting bolts in the base frame secure the generator to the shipping pallet. Remove these bolts, lift the generator and remove the shipping pallet.

Secure the generator to the concrete pad using anchor hardware (not provided). See Figure 3-1. Anchor bolts must be long enough to extend through the generator mounting frame.

Table 3-1 Physical Dimensions

 

 

 

 

 

 

 

Generator

Height

Width

Length

 

Weight

Model

Open

 

Enclosed

 

 

 

 

AE8−E/O

36.75

29.00

44.5

255 lbs.

 

463 lbs.

AE10−E/O

36.75

29.00

44.5

316 lbs.

 

509 lbs.

AE11−E

30.50

30.375

46

 

 

468 lbs.

AE25−E−NG

34.00

31.5.0

72

 

 

1450 lbs.

AE25−E−LP

34.00

31.5.0

72

 

 

1450 lbs.

3-4 Receiving & Installation

MN2415

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Automatic Emergency Generator California Proposition 65 Warning Table of Contents Appendix a Appendix BAppendix C Appendix DSection Product Safety Information Read This Manual ThoroughlySymbols OperationOperation Warning Statements Burn Installation Maintenance Product Safety Information MN2415 Limited Warranty Warranty Period Generator SeriesSection General Information Labor PartsGeneral Information MN2415 Section Receiving & Installation AE8 & AE10AE11 AE25Engine Cooling Indoor Location Ventilation TestHot Exhaust Gasses Guidelines for Exhaust SystemGenerator Height Width Length Weight Model Open Enclosed Physical DimensionsSecure the Generator Fuel Connections Fuel Consumption Natural and LPGGeneral Considerations Example Determining Pipe Size for Natural GasNatural Gas Connections Pipe Iron Pipe Size LengthExample Determining Pipe Size for LPG LP Gas Flow Rate Cubic Feet per Hour per Pipe LengthBattery Charger Considerations Transfer Switch ConsiderationsPhase VAC Rating Amps General Wiring Considerations Single Phase Power ConnectionsRemote Start and Battery Charger Connections AE8 with Enclosure or OpenAE10 with Enclosure AE10 Open AE10 With EnclosureAE11 with Enclosure TBP10 Remote Start & Battery Connections AE25 with Enclosure Natural Gas or LPGFrame Ground Connection Coolant LevelPage 12 Battery Installation Recommended Engine Oil and Battery TypePost Installation Checks Post Installation Checks Receiving & Installation MN2415 Section Operation Master Control Switch Natural/LP Gas Selector SwitchDisplay Lamps MetersManual Start/Stop All models Automatic Fault Shutdown AE11 and AE25Automatic Start/Stop All models Auto Start Operation AE11 Operating ProceduresShutdowns Editing the Configuration Access Configuration Editor FigureProgrammable Functions and Values 1Programmable Functions and Values Auxiliary Output Engine Controller Terminal Identification Electrical ConnectionsGarretson Model KN Fuel Valve Considerations General Service Garretson KN Fuel ValveSection Troubleshooting and Maintenance EngineProblems and Solutions General Troubleshooting GuideTroubleshooting Guide Digital Controller Only Troubleshooting Guide Analog Controller Only Operator Panel Configuration Master Control Switch Controller Fuse LampAppendix a Series AE8 Circuit BreakerFigure A-2 Alternator Assembly Table A-1Generator Set Parts List Figure A-4 AE8 Customer Connection Diagram Figure A-5 AE8 Open Frame Wiring Diagram Figure A-6 AE8 Enclosed Wiring Diagram Appendix B Series AE10 Figure B-1 AE10 Operator PanelFigure B-2 Alternator Assembly Table B-1Generator Set Parts List Figure B-4 AE10 Customer Connection Diagram Figure B-5 AE10 Open Frame Wiring Diagram Figure B-6 AE10 Enclosed Wiring Diagram Appendix C Series AE11 Figure C-1 AE11 Operator PanelReplacement Parts Figure C-2 Alternator AssemblyTable C-1Generator Set Parts List Conversion from LPG to Natural Gas Optional ProcedureFigure C-5 Figure C-7 AE11 Customer Connection Diagram Figure C-8 AE11 Generator Connection Diagram Figure C-9 AE11 Engine Connection Diagram Figure C-10 AE11 Connection Diagram Figure C-11 AE11 Customer Wiring Interface Diagram Series AE11 MN2415 Appendix D Series AE25 Figure D-1 AE25 Operator PanelFigure D-2 Alternator Assembly Table D-1 Generator Set Parts ListTable D-1Generator Set Parts List Figure D-4 AE25 Receptacle Connection Diagram Figure D-5 AE25 Engine Compartment Connection Diagram Figure D-6 AE25 Control Box Connection Diagram Baldor District Offices California Proposition 65 Warning

AE8, AE25, AE10, AE11 specifications

Baldor Electric Company has long been a trusted name in the manufacturing of electric motors and drives. Among their impressive lineup of products, the AE series, which includes the AE11, AE25, AE10, and AE8 models, stands out for their innovative features and robust performance, making them suitable for a variety of industrial applications.

The Baldor AE11 is designed with high efficiency in mind, ensuring that it consumes less energy while delivering optimal performance. This motor features a robust design that enhances durability and reliability, making it ideal for heavy-duty applications. The AE11 also incorporates advanced thermal management technology, ensuring that the motor remains cool even during prolonged use. Its compact size allows for easier integration in tight spaces, making it a versatile choice for many machinery types.

The AE25 model takes performance a step further with its enhanced power output and torque capabilities. This model is built for demanding environments and is engineered to reduce vibration and noise, providing a smoother operational experience. The AE25 also features built-in thermal protection, which automatically shuts down the motor in case of overheating, thereby safeguarding the equipment and reducing maintenance costs.

For those needing a more compact solution, the AE10 offers a balance of power and size. This electric motor is designed with a lightweight yet sturdy build, providing a perfect fit for smaller machines without sacrificing performance. The AE10 is equipped with high-energy efficiency ratings, contributing to lower operational costs and reduced environmental impact. Additionally, it supports various mounting options, enhancing its adaptability for different applications.

Lastly, the AE8 model is a true powerhouse for applications where space is at a premium. It features a minimalist design while still delivering reliable performance. The AE8 is optimized for energy efficiency, boasting a streamlined motor design that minimizes wasted energy. With its quiet operation and low maintenance requirements, this model is ideal for environments where noise reduction is essential.

In summary, the Baldor AE series—including the AE11, AE25, AE10, and AE8—shows a real commitment to efficiency, durability, and versatility. Each model is tailored to meet specific industry needs, whether for demanding heavy-duty applications or compact, energy-efficient setups. With their innovative technologies and engineering excellence, Baldor motors continue to set the standard in the electric motor industry.
Top Page Image Contents