Sears Comprehensive Service Manual for Snow Blower Models 536.886331

Page 17

CUSTOMER RESPONSIBILITIES

SERVICE RECORDS

SCHEDULE

Fill In dates as you com-

	plete regular service	After	Before [		Every	Every
	plete regular service	First 2	Each	As	10	25	Each	Before
		First 2	Each	As	10	25	Each	Before
		hours	Use	Needed	Hours	Hours	Season	Storage

SERVICE DATES

Check	Engine Oil Level '		p,4	pJ
Change	Engine Oil	_	Jr_	/_
Tighten All Screws and Nuts		_	_
Check Traction Clutch Cable
Adjustment (See Cable Adjustment)		PJ
Replace Spark Plug			pJ	pJ
_justDAveBolts		ii'	_,	_'
Lubricate All Pivot Points			_
LubricateAugerShaft(SeeShear				p,_
Bolt Replacement)
LubricateDiscDrivePlateZerk			f,_
DrainFuel				f_
Check Auger ClutchCable
Adjustment (See Cable Adjustment)		P'/		PJ

GENERAL RECOMMENDATIONSLUBRICATION CHART

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negli- gence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual.

Some adjustments will need to be made periodically to propedy maintain your snow thrower.

All adjustments in the Service and Adjustments section of this manual should be checked at least once each

season.

AFTER FIRST USE

•Check for any loose or damaged parts.

•Tighten any loose fasteners,

•Check and maintain the auger.

•After each use, remove all snow and slush off the snow thrower to prevent freezing of auger or controls.

•Check contrc!s to make sure they are functioning properly.

•If any parts are worn or damaged, replace immedi- ately.

17

Image 17

Contents Give the Following Information Product Snow Thrower When Ordering Repair PARTS, AlwaysModel Number Engine Model Number Part Number Part DescriptionBefore USE Fuel SafetyOperating Safety Safe Storage Safety RulesREPAIR/ADJUSTMENTS Safety Spark Plug Aintenance AgreementJstomer Responsibilities Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Snow Thrower Measuring tape or ruLerTo Install the Upper Handle and Crank Assembly HOW to SET UP Your Snow ThrowerTo Assemble Snow Chute Roll snow thrower off the skid by pulling on the handlePLASTIC\ Notchedsection To Install HeadlightTo Assemble Control Cables Parts section of this manualTo Install Shifter Lever Knob To Install the Shifter LeverVerse OperationThrower HOW to USE Your SnowTo Stop Your Snow Thrower To Move Forward and BackwardBefore Starting the Engine OperationTo USE Wheel Lockout PIN Fill OILTo Stop Engine Run the engine at full throttle RUN when throwingWarm Start RequiredFrozen Recoil Starter To Start Engine Recoil StarterSnow Throwing Tips General Recommendationslubrication Chart Service Records ScheduleService Dates Customer ResponsibilitiesLubrication Every 25 Hours Snow ThrowerLubrication Every TEN Hours Lubrication EngineRecommended Viscosity Grades COLDER--i2 --WARMER 5W30SAE30To Adjust Skid Height Service and AdjustmentsTo Adjust Scraper BAR To Adjust Chute Crank AssemblyAdjustments ServiceTo Adjust the Clutch Control Cables To Adjust BeltsDOORS, Away from Fire or Flame To Replace BeltsAuger Drive Belt To Adjust the Friction Wheel To Adjust the Belt GuidesTraction Drive Belt Remove the belt cover See in this sectionAway from Fire or Flamf To Replace Friction WheelRemove the bottom panel See FIG LBOTTOMPANELLocknut To Adjust CarburetorTo Replace Auger Shear Bolt To Adjust To Adjust or ReplaceSpark Plug To ReplaceSnow Thrower Storage StorageEngine Storage OtherTrouble Trouble Shooting PointsCause Correction