Sears 536.886331 Snow Thrower, Lubrication Every TEN Hours, Lubrication Every 25 Hours

Page 18

CUSTOMER RESPONSIBILITIES

SNOW THROWER

LUBRICATION - EVERY TEN HOURS

Auger Shaft - Using a hand grease gun, lubricate the auger shaft zerk fittings (See A, FIG, 2) every ten (10) operating hours. Each time a shear bolt is replaced

(See To Replace Auger Shear Bolt paragraph in the Service & Adjustments eectlon of this manual), the auger shaft MUST be greased.

For storage or when replacing shear bolts, remove shear bolts and lubricate auger shaft zerks. Rotate augers several times on the ._haft and reinstall the shear bolts.

LUBRICATION - EVERY 25 HOURS

•Position speed selector lever in first gear.

•Place a coin or (a shim of equal thickness) between the rubber friction whee= and disc drive plate to pre- vent friction wheel contacting the friction disc.

Disc Drive Plate - Using a hand grease gun, lubricate with a Hi Temp EP M oly grease, zerk located beneath the disc drive plate (See FIG. 3 inset) every 25 hours and at the end of the season and/or before storage. To grease zerk, turn disc drive plate clockwise by hand until zerk is clearly visible at front center. DO NOT overfill or allow grease to come in contact with the disc drive plate or friction wheel or damage will result. Fill zerk only until grease becomes visible below bearing assembly located under grease zerk. See Lubrication Chart in this seCtion.

•IMPORTANT: Remove coin and ensure that a gap exists between friction wheel and disc drive plate.

•NOTE: Clean all excess grease found on friction disc hub.

-__AXLE

AXLE_

FIG. 1

FIG. 2

HEX SHAFT AND GEARS

FRICTION

WHEEL

DISC

DRIVE

PLATE

/

•CAUTION: Do not allow grease to contact friction wheel and disc drive plate.

FRICTION

WHEELGRF-ASI

LUBRICATION - BEFORE STORAGE

•Remove both wheels, grease (any automotive type grease) both axles (See FIG. 1) and replace wheels. Do this at least once a year and/or prior to storage.

ASSEMBLY

be visible

FIG. 3

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Engine Model Number When Ordering Repair PARTS, AlwaysGive the Following Information Product Snow Thrower Part Number Part DescriptionFuel Safety Operating SafetyBefore USE Safety Rules REPAIR/ADJUSTMENTS SafetySafe Storage Aintenance Agreement Jstomer ResponsibilitiesSpark Plug Table of Contents Contents of Hardware Pack To Remove Snow Thrower AssemblyTools Required for Assembly Measuring tape or ruLerTo Assemble Snow Chute HOW to SET UP Your Snow ThrowerTo Install the Upper Handle and Crank Assembly Roll snow thrower off the skid by pulling on the handleTo Assemble Control Cables To Install HeadlightPLASTIC\ Notchedsection Parts section of this manualTo Install the Shifter Lever To Install Shifter Lever KnobOperation VerseTo Stop Your Snow Thrower HOW to USE Your SnowThrower To Move Forward and BackwardTo USE Wheel Lockout PIN OperationBefore Starting the Engine Fill OILWarm Start Run the engine at full throttle RUN when throwingTo Stop Engine RequiredTo Start Engine Recoil Starter Frozen Recoil StarterSnow Throwing Tips Service Dates Service Records ScheduleGeneral Recommendationslubrication Chart Customer ResponsibilitiesSnow Thrower Lubrication Every TEN HoursLubrication Every 25 Hours Recommended Viscosity Grades EngineLubrication COLDER--i2 --WARMER 5W30SAE30To Adjust Scraper BAR Service and AdjustmentsTo Adjust Skid Height To Adjust Chute Crank AssemblyTo Adjust the Clutch Control Cables ServiceAdjustments To Adjust BeltsTo Replace Belts Auger Drive BeltDOORS, Away from Fire or Flame Traction Drive Belt To Adjust the Belt GuidesTo Adjust the Friction Wheel Remove the belt cover See in this sectionRemove the bottom panel See FIG To Replace Friction WheelAway from Fire or Flamf LBOTTOMPANELTo Adjust Carburetor To Replace Auger Shear BoltLocknut Spark Plug To Adjust or ReplaceTo Adjust To ReplaceEngine Storage StorageSnow Thrower Storage OtherCause Trouble Shooting PointsTrouble Correction
Top Page Image Contents