Sears 536.886331 owner manual Aintenance Agreement, Jstomer Responsibilities, Spark Plug

Page 4

CONGRATULATIONS on your purchase of a Sears _rattsman Snow Thrower. It has been designed, engi-

neered a_d manufactured to give you the best poss;ble

dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest Sears Service Center/Department. Sears has competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enab(e you to assemble and maintain your snow thrower oropedy. Always observe the "SAFETY RULES."

MODEL

NUMBER 536.886331

SERIAL

NUMBER

DATE OF

PURCHASE

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

i =

HORSE

POWER:

10 hp

DISPLACEMENT:

21.82

 

 

cu, in.

GASOLINE CAPACITY:

4 quarts

 

 

Unleaded

OIL (26

oz. Capacity):

5W - 30

SPARK PLUG :

Champion

 

(GAP .030 In.)

RJ19LM

 

VALVE CLEARANCE:

Intake:

.010 In.

 

Exhaust:

.010 In.

AINTENANCE AGREEMENT

Sears Maintenance Agreement is available on this )duct. Contact your nearest Sears Store for details.

JSTOMER RESPONSIBILITIES

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and using your snow thrower.

Follow the instructions under "Customer Responsibilities" and "Storage" sections of this owner's manual.

TWO YEAR LIMITED WARRANTY ON CRAFTSMAN

SNOW THROWER

For two years from the date of purchase, when this Craftsman Snow Thrower is maintained, lubricated and tuned-upaccording to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and workmanship.

If this Craftsman Snow Thrower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty does not cover the following:

Expendable items which become worn during normal use, such as spark plugs, drive belts and shear pins.

Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual.

VARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN SNOW THROWER TO THE _EAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. THIS WARRANTY ,PPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES.

his warranty gives you specific legal rights, and you may also have other rights which may vary from ate to state.

SEARS, ROEBUCK AND CO. Department D/817WA, Hoffman Estates, IL 60179

Image 4
Contents When Ordering Repair PARTS, Always Give the Following Information Product Snow ThrowerModel Number Engine Model Number Part Number Part DescriptionOperating Safety Fuel SafetyBefore USE REPAIR/ADJUSTMENTS Safety Safety RulesSafe Storage Jstomer Responsibilities Aintenance AgreementSpark Plug Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Snow Thrower Measuring tape or ruLerHOW to SET UP Your Snow Thrower To Install the Upper Handle and Crank AssemblyTo Assemble Snow Chute Roll snow thrower off the skid by pulling on the handleTo Install Headlight PLASTIC\ NotchedsectionTo Assemble Control Cables Parts section of this manualTo Install the Shifter Lever To Install Shifter Lever KnobOperation VerseHOW to USE Your Snow ThrowerTo Stop Your Snow Thrower To Move Forward and BackwardOperation Before Starting the EngineTo USE Wheel Lockout PIN Fill OILRun the engine at full throttle RUN when throwing To Stop EngineWarm Start RequiredTo Start Engine Recoil Starter Frozen Recoil StarterSnow Throwing Tips Service Records Schedule General Recommendationslubrication ChartService Dates Customer ResponsibilitiesLubrication Every TEN Hours Snow ThrowerLubrication Every 25 Hours Engine LubricationRecommended Viscosity Grades COLDER--i2 --WARMER 5W30SAE30Service and Adjustments To Adjust Skid HeightTo Adjust Scraper BAR To Adjust Chute Crank AssemblyService AdjustmentsTo Adjust the Clutch Control Cables To Adjust BeltsAuger Drive Belt To Replace BeltsDOORS, Away from Fire or Flame To Adjust the Belt Guides To Adjust the Friction WheelTraction Drive Belt Remove the belt cover See in this sectionTo Replace Friction Wheel Away from Fire or FlamfRemove the bottom panel See FIG LBOTTOMPANELTo Replace Auger Shear Bolt To Adjust CarburetorLocknut To Adjust or Replace To AdjustSpark Plug To ReplaceStorage Snow Thrower StorageEngine Storage OtherTrouble Shooting Points TroubleCause Correction