Sears 944.529571 owner manual HOW to USE Your Snow Thrower, Times including startup

Page 11

PE

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result insevere eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any adjust-

ments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

Release the auger control lever to stop throwing snow.

ENGINE

1. Move ON / OFF switch to "OFF" position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE THROTTLE CONTROL (See Fig. 11)

The throttle control is located on the engine. Always operate the snow thrower with the engine at full throttle. Full throttle offers the best snow thrower performance.

FAST

FIG. 11

TO USE CHOKE CONTROL (See Fig. 12)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

FIG. 12

TO CONTROL SNOW DISCHARGE (See Fig. 13)

WARNING: Snow throwers have ex=

posed rotating parts, which can cause severe injury from contact, or from ma= terial thrown from the discharge chute.

Keep the area of operation clear of all persons, small children and pets at all

times including startup.

WARNING: if the discharge chute or

and wait for all moving parts to stop. Use

_I auger become clogged,shut=off engine the clean=out tool, NOT YOUR HANDS,

to unclo the chute and/or au er.

The DIRECTION in which snow isto be thrown is controlled by the discharge chute control lever.

To change the discharge chute position, press down- ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to

throw snow a short distance; set the deflector higher to throw snow farther.

Press downward on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROLLEVER

CHUTE DEFLECTOR

REMOTE CONTROLLEVER

FIG. 13

11

Image 11
Contents OW TH SE IES E E 27 TWO-STAGEPowe -P Elle Safe Operation Practices for Walk-Behind Snow Throwers Contents Page Shearboltsandnuts Parts Packe ELY I CartonOperatio See Figs Install Traction Drive Control RODAsse BLY/PRE-OPERATION Unfold Upper HandleOperatic Install Discharge Chute / Chute RotaterASS Check TiRE Pressure RUN Pull OUT to Stop Disengaged Know Your Snow ThrowerOr Warning Ignition KEYOperati Meets A.N.SJ. Safety RequirementsTo unclo the chute and/or au er HOW to USE Your Snow ThrowerTimes including startup To Throw Snow See Fig OperationBefore Starting the Engine Before Stopping To Start EngineFill in Dates General RecommendationsBefore Each USE Snow ThrowerEngine CleaningEquipment shear bolts as supplied with your snow thrower To Adjust Snow Thrower HeightSeadj Ents Seadj Engine Speed CarburetorEngine OIL StorageOther Fuel SystemOTI Problem\17 DESCRiPTiON Description KEY Part DescriptionDescription Auger Bearing Bearing Plug Description Skid Plate LH Skid Plate RHPart Control Panel / Discharge ChuteDescription Interlock HandlesSpacer Repair Partssnow Thrower - Model Number 944,529571Shifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPPanel Console Wire HarnessLower Tube Pivot SupportRepair Parts Snow Thrower - Model Number 944,529571 Drive Wheel HUB Rubber Ring AssemblyDrive Plate Assembly Speed SelectorTH Rust Wash ER Axle AssemblyAxle Shaft SprocketEngine Model Chassis / PulleysKEY Part Description Engine Mount PlateCover Assembly Idler ARM ImpellerIdler Pulley ENG ImpellerBellcrank Steering BracketPivot Bracket Wheel DriverCable Bracket Wheel AssemblyPart Description Locknut 3/8-16 Washer 3/8 Safety Ignition KEYBAG of Parts KEY Part NO. noKEY Part Decals161 Briggs & Stratton 4-CYCLE EngineModel Number 20M314-1370-E2 528j!i Cycle Engine Briggs & StrattonEngine Power Rating information Service Notes 800-.4-.MY-.HOME