Sears 944.529571 Asse BLY/PRE-OPERATION, Unfold Upper Handle, Install Traction Drive Control ROD

Page 6

ASSE BLY/PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments

to the skid plates.

UNFOLD UPPER HANDLE

. Raise upper handle to the operating position and

tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD_

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD

RETAINER

SPRING

SPEEDSPEED

CONTROL CONTROL

BRACKETLEVER

FIG, 2

INSTALL TRACTION DRIVE CONTROL ROD

(See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securing rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

\\

\

FIG. 3

DRIVE RETAINER

SPRING

CONTROL

BRACKET

FIG. 4

6

Image 6

Contents SE IES E E 27 TWO-STAGE Powe -P ElleOW TH Safe Operation Practices for Walk-Behind Snow Throwers Contents Page Parts Packe ELY I Carton OperatioShearboltsandnuts Unfold Upper Handle Install Traction Drive Control RODAsse BLY/PRE-OPERATION See FigsInstall Discharge Chute / Chute Rotater ASSOperatic Check TiRE Pressure Ignition KEY Know Your Snow ThrowerOr Warning RUN Pull OUT to Stop DisengagedMeets A.N.SJ. Safety Requirements OperatiHOW to USE Your Snow Thrower Times including startupTo unclo the chute and/or au er Operation To Throw Snow See FigBefore Starting the Engine To Start Engine Before StoppingSnow Thrower General RecommendationsBefore Each USE Fill in DatesCleaning EngineTo Adjust Snow Thrower Height Seadj EntsEquipment shear bolts as supplied with your snow thrower Seadj Carburetor Engine SpeedFuel System StorageOther Engine OILProblem OTI\17 DESCRiPTiON KEY Part Description DescriptionDescription Skid Plate LH Skid Plate RH Description Auger Bearing Bearing PlugControl Panel / Discharge Chute PartDescription Handles InterlockRepair Partssnow Thrower - Model Number 944,529571 SpacerShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomPivot Support Wire HarnessLower Tube Panel ConsoleRepair Parts Snow Thrower - Model Number 944,529571 Drive Speed Selector Rubber Ring AssemblyDrive Plate Assembly Wheel HUBSprocket Axle AssemblyAxle Shaft TH Rust Wash EREngine Mount Plate Chassis / PulleysKEY Part Description Engine ModelCover Assembly ENG Impeller ImpellerIdler Pulley Idler ARMWheel Driver Steering BracketPivot Bracket BellcrankWheel Assembly Part DescriptionCable Bracket KEY Part NO. no Safety Ignition KEYBAG of Parts Locknut 3/8-16 Washer 3/8Decals KEY PartBriggs & Stratton 4-CYCLE Engine 161Model Number 20M314-1370-E2 528j!i Briggs & Stratton Cycle EngineEngine Power Rating information Service Notes 800-.4-.MY-.HOME