Sears 944.529571 owner manual Ass, Operatic, Install Discharge Chute / Chute Rotater

Page 7

ASS

LY / P

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

E-OPERATIC

INSTALL DISCHARGE CHUTE / CHUTE ROTATER

HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces-

sary, rotate chute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and Iocknut on threaded stud and tighten securely.

AUGER

ROD

\

CONTROL

ARM

FIG. 5

AUGER CONTROL ROD AUGER CONTROL

RETAINER LEVER

SPRING\

CONTROL

BRACKET

CHUTE

ROTATER_3/8LOCKNUT

HEAD

_3/8WASHER

PIN

STUD

ROTATER HEAD

MOUNTING

BRACKET

FIG. 7

FIG. 6

Image 7

Contents Powe -P Elle SE IES E E 27 TWO-STAGEOW TH Safe Operation Practices for Walk-Behind Snow Throwers Contents Page Operatio Parts Packe ELY I CartonShearboltsandnuts See Figs Install Traction Drive Control RODAsse BLY/PRE-OPERATION Unfold Upper HandleASS Install Discharge Chute / Chute RotaterOperatic Check TiRE Pressure RUN Pull OUT to Stop Disengaged Know Your Snow ThrowerOr Warning Ignition KEYOperati Meets A.N.SJ. Safety RequirementsTimes including startup HOW to USE Your Snow ThrowerTo unclo the chute and/or au er To Throw Snow See Fig OperationBefore Starting the Engine Before Stopping To Start EngineFill in Dates General RecommendationsBefore Each USE Snow ThrowerEngine CleaningSeadj Ents To Adjust Snow Thrower HeightEquipment shear bolts as supplied with your snow thrower Seadj Engine Speed CarburetorEngine OIL StorageOther Fuel SystemOTI Problem\17 DESCRiPTiON Description KEY Part DescriptionDescription Auger Bearing Bearing Plug Description Skid Plate LH Skid Plate RHPart Control Panel / Discharge ChuteDescription Interlock HandlesSpacer Repair Partssnow Thrower - Model Number 944,529571Shifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPPanel Console Wire HarnessLower Tube Pivot SupportRepair Parts Snow Thrower - Model Number 944,529571 Drive Wheel HUB Rubber Ring AssemblyDrive Plate Assembly Speed SelectorTH Rust Wash ER Axle AssemblyAxle Shaft SprocketEngine Model Chassis / PulleysKEY Part Description Engine Mount PlateCover Assembly Idler ARM ImpellerIdler Pulley ENG ImpellerBellcrank Steering BracketPivot Bracket Wheel DriverPart Description Wheel AssemblyCable Bracket Locknut 3/8-16 Washer 3/8 Safety Ignition KEYBAG of Parts KEY Part NO. noKEY Part Decals161 Briggs & Stratton 4-CYCLE EngineModel Number 20M314-1370-E2 528j!i Cycle Engine Briggs & StrattonEngine Power Rating information Service Notes 800-.4-.MY-.HOME