Sears 944.529571 owner manual Carburetor, Engine Speed

Page 19

SE iCE ADJ ENTS

TO REMOVE WHEELS (See Fig. 23)

Remove the klik pin and remove wheel from axle.

iMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft - do not use the

hole in the wheel hub (if equipped). Inner hole in axle and hole inwheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PiN	(iNSTALL	OUTER HOLE
iN OUTER	HOLE
OF AXLE	ONLY)

AXLE

WHEELWHEELHUB

FiG. 23

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a Sears or other qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG, 24

19

Image 19

Contents Powe -P Elle SE IES E E 27 TWO-STAGEOW TH Safe Operation Practices for Walk-Behind Snow Throwers Contents Page Operatio Parts Packe ELY I CartonShearboltsandnuts See Figs Install Traction Drive Control RODAsse BLY/PRE-OPERATION Unfold Upper HandleASS Install Discharge Chute / Chute RotaterOperatic Check TiRE Pressure RUN Pull OUT to Stop Disengaged Know Your Snow ThrowerOr Warning Ignition KEYOperati Meets A.N.SJ. Safety RequirementsTimes including startup HOW to USE Your Snow ThrowerTo unclo the chute and/or au er To Throw Snow See Fig OperationBefore Starting the Engine Before Stopping To Start EngineFill in Dates General RecommendationsBefore Each USE Snow ThrowerEngine CleaningSeadj Ents To Adjust Snow Thrower HeightEquipment shear bolts as supplied with your snow thrower Seadj Engine Speed CarburetorEngine OIL StorageOther Fuel SystemOTI Problem\17 DESCRiPTiON Description KEY Part DescriptionDescription Auger Bearing Bearing Plug Description Skid Plate LH Skid Plate RHPart Control Panel / Discharge ChuteDescription Interlock HandlesSpacer Repair Partssnow Thrower - Model Number 944,529571Shifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPPanel Console Wire HarnessLower Tube Pivot SupportRepair Parts Snow Thrower - Model Number 944,529571 Drive Wheel HUB Rubber Ring AssemblyDrive Plate Assembly Speed SelectorTH Rust Wash ER Axle AssemblyAxle Shaft SprocketEngine Model Chassis / PulleysKEY Part Description Engine Mount PlateCover Assembly Idler ARM ImpellerIdler Pulley ENG ImpellerBellcrank Steering BracketPivot Bracket Wheel DriverPart Description Wheel AssemblyCable Bracket Locknut 3/8-16 Washer 3/8 Safety Ignition KEYBAG of Parts KEY Part NO. noKEY Part Decals161 Briggs & Stratton 4-CYCLE EngineModel Number 20M314-1370-E2 528j!i Cycle Engine Briggs & StrattonEngine Power Rating information Service Notes 800-.4-.MY-.HOME