Poulan 435551 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot

Page 26

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

CONTROL PANEL / CHUTE

2

2

*3

1

*7

*6

KEY

PART

DESCRIPTION

 

 

 

NO.

NO.

 

 

 

1

428272

LEVER/CABLE ROTATOR ASSEMBLY

*4

01.09.010-B

*5

2

17501010

SCREW 10-24 X .625

 

 

 

 

*3

420678

ROTATOR HEAD

 

 

 

*4

405932

ROTATOR PIVOT BRACKET

 

 

 

*5

420675

PULLEY PIVOT

 

 

 

*6

428273

CABLE ASSEMBLY ADJUSTABLE

 

 

 

*7

428310

CABLE ASSEMBLY HEAT SHIELD

 

 

 

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

2

101.15.009-A

KEY

PART

DESCRIPTION

NO.

NO.

1

421249

STEER CABLE

2

74041024

SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs a and 8B Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Auger Assembly RH Auger HousingAuger Assembly LH KEY Part DescriptionExploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller PulleySkid Plate LH Auger BearingBearing Plug Skid Plate RHChute Snow Shield 419822X431 Shield Retainer Strap Knob BlackPOP Rivet Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketWasher 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Lower HandleKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightAxle Shaft SprocketExploded Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate427963X428 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyCable Bracket LH 432333X421 Wheel Assembly LH 432334X421 Wheel Assembly RH01.06.017-A Cable Bracket RHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 422663DECAL, Instruction DECAL, DangerDECAL, DANGER, Deflector DECAL, Speed ControlLimited Warranty
Top Page Image Contents