Poulan 435551 owner manual Operation, Meets A.N.S.I. Safety Requirements

Page 9

MEETS A.N.S.I. SAFETY REQUIREMENTS

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL (AUXILIARY) STARTER HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ELECTRIC AUGER

START CONTROL

BUTTON LEVER

POWER

CORD

PLUG

CHUTE

DEFLECTOR

DISCHARGE

CHUTE

CLEAN-OUT TOOL

Fig. 9

DISCHARGE CHUTE	DEFLECTOR REMOTE
CONTROL LEVER	CONTROL LEVER
DRIVE SPEED	TRACTION
CONTROL LEVER	DRIVE
	CONTROL
	LEVER

LH TURN

TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

ON / OFF switch - used to STOP the engine. Choke control - used for starting a cold engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9

Image 9

Contents IMPORTANT MANUAL SNOW THROWERPP208EPS24 Do Not Throw AwayTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE PLASTIC TIEINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andALIGN BEFORE TIGHTENING LOCKNUTCHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8A and 8BKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER POWER STEERING OPERATION See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGV-BELTS AUGER GEAR CASESERVICE AND ADJUSTMENTS TO REPLACE BELTS See Fig KLIK PIN INSTALL TO ADJUST CABLE TENSION See FigADJUSTER TURN TO REMOVE WHEELS See FigOTHER STORAGEFUEL SYSTEM ENGINE OILTROUBLESHOOTING AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS2401.07.026-D 2 EXPLODEDAUGER HOUSING / IMPELLER ASSEMBLY 01.07.024-B 01.11.001-B8 01.09.015-B CONTROL PANEL / CHUTE01.09.010-B 101.15.009-A01-05-013-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLESREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLES 01.12.001-E 01.08.007-B REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 01.02.013-A 42 EXPLODEDREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE CHASSIS / ENGINE / PULLEYS COVER ASSEMBLY01.21.013-B 01.21.003-C SHOULDER BOLT 5/16-1801.15.003-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 WHEELS1 01.15.001-A 01.14.009-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 BAG OF PARTSREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DECALS LIMITED WARRANTY