Poulan 435551 REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLES, 01-05-013-A

Page 27

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

HANDLES

			5
				1
			6
		8		7
		2
5	8		3	9
	8
	6		7
			7
	8
	4	9

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1419800X431 PLOW HANDLE LH

2419801X431 PLOW HANDLE RH

3196944X431 PANEL BRACKET LH

4196943X431 PANEL BRACKET RH

5

199513

HANDLE GRIP

674780512 SCREW 5/16−18 X .750

774780524 SCREW 5/16−18 X 1.50

8	751153	NUT 5/16−18
9	155415	WASHER

01.08.003-A

1

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	419797X431	LOWER HANDLE
	2	427513X431	PIVOT SUPPORT WELDMENT
	3	428867	SCREW 5/16−18 X .750
2	4	17000616	SCREW 3/8−16 X 1.00

4

4

3

4

3

4

01-05-013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

27

Image 27

Contents Do Not Throw Away SNOW THROWERIMPORTANT MANUAL PP208EPS24Operation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StorageREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER PARTS PACKED SEPARATELY IN CARTONPLASTIC TIE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and UNFOLD UPPER HANDLETIGHTENING LOCKNUT INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig ALIGN BEFORECHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8A and 8BKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER TO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSTO START ENGINE BEFORE STOPPINGLUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTSSERVICE AND ADJUSTMENTS TO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigKLIK PIN INSTALL ADJUSTER TURNENGINE OIL STORAGEOTHER FUEL SYSTEMTROUBLESHOOTING AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS2401.07.026-D 2 EXPLODEDDESCRIPTION 01.07.024-B 01.11.001-B8 01.09.015-B CONTROL PANEL / CHUTE01.09.010-B 101.15.009-A01-05-013-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLESREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLES 01.12.001-E 01.08.007-B REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 01.02.013-A 42 EXPLODEDREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE CHASSIS / ENGINE / PULLEYS COVER ASSEMBLY01.21.013-B 01.21.003-C SHOULDER BOLT 5/16-1801.15.003-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 WHEELS1 01.15.001-A 01.14.009-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 BAG OF PARTSREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DECALS LIMITED WARRANTY