Poulan 435551 REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 WHEELS, 1 01.15.001-A

Page 37

1 01.15.001-A

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

WHEELS

2

17

16

20

19 21

2				7
	3	4	5	6
2	1 01.15.001-A

				17					3	2
		20		17		23		4	3	1
		20		19			6	5
		16					6	5
	18	16		22			7
		15	18	22		9	7
		15	18			9	8
		24				10
		23				10
		23		21		11
		22
						12
					13	14
				14 13	13
		11		14 13
	10			12
8	9
				KEY		PART	DESCRIPTION
				NO.		NO.	DESCRIPTION
				1		405161	COVER
				2		184471	SHOULDER SCREW

312000045 RETAINER RING

4192126 WHEEL DRIVER

5182466 RETAINER RING

6	187622	WHEEL LOBE
7	194941	CLUTCH SLIDE
8	179139	SPRING
9	189282	SQUARE KEY
10	194940	AXLE LOBE
11	174697	THRUST WASHER

12193506X431 STEERING YOKE

13179148X431 STEERING BRACKET

1417490508 SCREW 5/16−18 X .50

15194943X008 PIVOT BRACKET

16194944X008 BELLCRANK

17181847 BELLCRANK PIN

1817600406 SCREW 1/4−20 X .375

19405077 STEERING LINK

20	700279	RETAINER
21	85179	RETAINER
22	193885	SPRING
23	182015	LEVER PIN
24	194939X008	PIVOT BRACKET

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

37

Image 37

Contents IMPORTANT MANUAL SNOW THROWERPP208EPS24 Do Not Throw AwayTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage CUSTOMER RESPONSIBILITIESHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE PLASTIC TIEINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andALIGN BEFORE TIGHTENING LOCKNUTCHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8A and 8BKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER POWER STEERING OPERATION See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig CHECK ENGINE OIL LEVEL See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGV-BELTS AUGER GEAR CASESERVICE AND ADJUSTMENTS TO REPLACE BELTS See Fig KLIK PIN INSTALL TO ADJUST CABLE TENSION See FigADJUSTER TURN TO REMOVE WHEELS See FigOTHER STORAGEFUEL SYSTEM ENGINE OILTROUBLESHOOTING AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS2401.07.026-D 2 EXPLODEDAUGER HOUSING / IMPELLER ASSEMBLY 01.07.024-B 01.11.001-B8 01.09.015-B CONTROL PANEL / CHUTE01.09.010-B 101.15.009-A01-05-013-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLESPART 01.12.001-E 01.08.007-B REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 01.02.013-A 42 EXPLODEDREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE COVER ASSEMBLY CHASSIS / ENGINE / PULLEYS01.21.013-B 01.21.003-C SHOULDER BOLT 5/16-1801.15.003-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 WHEELS1 01.15.001-A 01.14.009-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 BAG OF PARTSREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DECALS LIMITED WARRANTY