Poulan 435551 REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24, Chassis / Engine / Pulleys

Page 35

SHOULDER BOLT 5/16-18 X .500

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14
24			21
			20			KEY	PART
						KEY	PART	DESCRIPTION
11						NO.	NO.	DESCRIPTION
14	21			19		1	408007	IMPELLER BELT
14	21		20	19		2	419744	TRACTION BELT
13				18		2	419744	TRACTION BELT
						3	423723X431	IDLER ARM BRACKET
						3	423723X431	IDLER ARM BRACKET
				17		4	180523	IDLER PULLEY
12				17		5	426589	NUT 5/16-18
12				16		5	426589	NUT 5/16-18
14		15		16		6	74780524	SCREW 5/16-18 X 1 .50
		15	6			7	423990X431	IDLER BRACKET
			6			7	423990X431	IDLER BRACKET
7						8	428867	SCREW 5/16-18 X .625
7						9	424297	SHOULDER BOLT 5/16-18 X .500
10						9	424297	SHOULDER BOLT 5/16-18 X .500
10						10	751153	NUT 5/16-18 NYLOCK
				5		10	751153	NUT 5/16-18 NYLOCK
				5		11	187786	TRACTION IDLER ARM
8				4		11	187786	TRACTION IDLER ARM
				4		12	180522	TRACTION PULLEY
				3		12	180522	TRACTION PULLEY
						13	74780520	SCREW 5/16-18 X 1 .00
						14	59289	WASHER
				9		15	73800500	NUT 5/16-18
					1	16	851084	SCREW 3/8-24 X 1.375
					1	17	400026	WASHER
						17	400026	WASHER
				2		18	426491	PULLEY ENG IMPELLER
						19	426490	PULLEY ENG TRACTION
						20	74610516	SCREW 5/16-18 X 1 .00
		01.21.003-C				21	10040500	LOCKWASHER 5/16
						22	155452	BELT GUIDE
						23	11050500	LOCKWASHER 5/16
						24	175331	IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 35

Image 35

Contents Do Not Throw Away SNOW THROWERIMPORTANT MANUAL PP208EPS24Operation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StorageREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER PARTS PACKED SEPARATELY IN CARTONPLASTIC TIE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and UNFOLD UPPER HANDLETIGHTENING LOCKNUT INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig ALIGN BEFORECHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8A and 8BKNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER TO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSTO START ENGINE BEFORE STOPPINGLUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTSSERVICE AND ADJUSTMENTS TO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigKLIK PIN INSTALL ADJUSTER TURNENGINE OIL STORAGEOTHER FUEL SYSTEMTROUBLESHOOTING AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS2401.07.026-D 2 EXPLODEDDESCRIPTION 01.07.024-B 01.11.001-B8 01.09.015-B CONTROL PANEL / CHUTE01.09.010-B 101.15.009-A01-05-013-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLESDESCRIPTION 01.12.001-E 01.08.007-B REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 01.02.013-A 42 EXPLODEDREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 01.21.013-B CHASSIS / ENGINE / PULLEYSCOVER ASSEMBLY 01.21.003-C SHOULDER BOLT 5/16-1801.15.003-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 WHEELS1 01.15.001-A 01.14.009-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 BAG OF PARTSREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DECALS LIMITED WARRANTY