Poulan 435551 REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 BAG OF PARTS, 01.14.009-A

Page 38

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002701)

BAG OF PARTS

3

2

01.14.003-B

			KEY	PART
4			NO.	NO.	DESCRIPTION
5		6	1	198563	POWER CORD
5		8	1	198563	POWER CORD
7		8	2	169675	RETAINER PIN
7			3	180684	WRENCH
			3	180684	WRENCH
			4	184505	REMOTE SPRING
		9 10	5	179829	SHOULDER BOLT 1/4-20
		9 10	6	191730	LOCKNUT 1/4-20
			7	72250505	CARRIAGE BOLT 5/16-18 X 5/8
			8	751153	LOCKNUT 5/16-18
			9	73800600	LOCKNUT 3/8-16
			10	19131316	WASHER 3/8
	1	12	11	192090	SHEAR BOLT 1/4-20 X 1-13/16
		12	12	73800400	LOCKNUT 1/4-20
		11	12	73800400	LOCKNUT 1/4-20
		11

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
1	1	422663	SAFETY IGNITION KEY
1

01.14.009-A

13

4

1

4

2

		2
01.14.012-A
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1180445 SHIFTER ROD TOP

2187716 SHIFTER ROD BOTTOM

372270505 CARRIAGE BOLT 5/16-18 X .75

4

155377

NUT 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38

Image 38

Contents PP208EPS24 SNOW THROWERIMPORTANT MANUAL Do Not Throw AwayPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationMaintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and PLASTIC TIEALIGN BEFORE INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD See Fig TIGHTENING LOCKNUTINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8A and 8B CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS HOW TO USE YOUR SNOW THROWER TO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See FigSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENBEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONV-BELTS CLEANINGENGINE AUGER GEAR CASESERVICE AND ADJUSTMENTS TO REPLACE BELTS See Fig ADJUSTER TURN TO ADJUST CABLE TENSION See FigKLIK PIN INSTALL TO REMOVE WHEELS See FigFUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 AUGER HOUSING / IMPELLER ASSEMBLY2 EXPLODED 01.07.026-DPART 01.11.001-B 01.07.024-BCONTROL PANEL / CHUTE 8 01.09.015-B101.15.009-A 01.09.010-BREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 HANDLES 01-05-013-ADESCRIPTION 01.12.001-E 01.08.007-B REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 42 EXPLODED 01.02.013-AREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DRIVE 01.21.013-B CHASSIS / ENGINE / PULLEYSCOVER ASSEMBLY SHOULDER BOLT 5/16-18 01.21.003-CREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 WHEELS 01.15.003-A1 01.15.001-A REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 BAG OF PARTS 01.14.009-AREPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 DECALS LIMITED WARRANTY