Poulan 435551 owner manual Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

Fig. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

Fig. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATOR		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATOR HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

6

Image 6

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs a and 8B Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Auger Assembly RH Auger HousingAuger Assembly LH KEY Part DescriptionExploded Bearing Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Impeller PulleySkid Plate LH Auger BearingBearing Plug Skid Plate RHKnob Black POP RivetChute Snow Shield 419822X431 Shield Retainer Strap Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketWasher 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip Lower HandleKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightAxle Shaft SprocketExploded Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate427963X428 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyCable Bracket LH 432333X421 Wheel Assembly LH 432334X421 Wheel Assembly RH01.06.017-A Cable Bracket RHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 422663DECAL, Instruction DECAL, DangerDECAL, DANGER, Deflector DECAL, Speed ControlLimited Warranty