Poulan 96194000500 HOW to SET UP Your Snow Thrower, Tool BOX See Fig, Unfold Upper Handle

Page 5

ASSEMBLY / PRE-OPERATION

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD

RETAINER

SPRING

SPEED SPEED

CONTROL CONTROL

BRACKET LEVER

FIG. 2

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING

TRACTION

DRIVE

CONTROL

ROD

DRIVE

CONTROL

BRACKET

FIG. 4

5

Image 5

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONInstall Speed Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Traction Drive Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other TroubleshootingFuncionamiento ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaPreparación Montaje / PRE-OPERACIÓN Sacar LA Máquina Quitanieves DEL Cartón Montaje / PRE-OPERACIÓNDesplegar LA Empuñadura Superior Como Preparar SU Máquina QuitanievesMontar LA Biela Montaje DE LA BielaControlar LA Presión DE LOS Neumáticos DE Mando DE LA Barrena Ver Figs yFamiliarícese CON SU Máquina Quitanieves OperaciónPlacas DE Pararse Controlar LA Eyección DE LA NieveComo Utilizar SU Máquina Quitanieves Usar LA Herramienta Para Limpiar Ver Fig Lanzar LA Nieve Ver FigMoverse Adelante Y Atrás Ver Fig Regular LAS Placas DE Deslizamiento Ver Fig Antes DE Poner EN Marcha EL MotorBarra DE Arrastre Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigPuesta EN Marcha DEL Motor Consejos Para Lanzar LA NieveAntes DE Parar SI EL Arrancador DE Retroceso SE HA CongeladoLubricación MantenamientoRecomendaciones Generales Limpieza Para Ajustar LA Altura DE Máquina Quitanieves Servicio Y AdjustesConducto Deflector Pernos DE Seguridad Ver FigVaciar LA Gasolina DEL Depósito DE Carburante Sustituir LAS Correas Vea FigOtros AlmacenimientoMotor Identificacion DE Problemas Page KEY Part Description 205 414280 Knob, Lever Repair Parts Handles Snow Thrower Model Number Repair Parts Snow Thrower Model Number 96194000500 Handles Repair Parts Snow Thrower Model Number 96194000500 Drive Repair Parts Snow Thrower Model Number 96194000500 Drive Page KEY Part Description Page 181038 Decal, Danger Limited Warranty