MTD 60-3754-4, 60-3753-6 manual Operating Your Snow Thrower

Page 10

Electric Starter Outlet (If so equipped)

Requires use of a three-prong outdoor extension cord (packed with the snow thrower) and a 120V power source/wall outlet.

Augers

When engaged, the augers rotate and draw snow into the housing.

Chute Assembly

Snow drawn into the auger housing is discharged out the chute assembly.

SECTION 4: OPERATING YOUR SNOW THROWER

Before Starting

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

Starting The Engine

•Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug.

•Make certain both the auger control and drive control are in the disengaged (released) position.

•Move throttle control up to FAST position. Insert

ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start unless the key is inserted into ignition switch.

Electric Starter (on models so quipped)

•Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

CAUTION: If your home’s wiring system

is not a three-wire grounded system, do not use this electric starter under any conditions.

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

WARNING: If your home electrical

system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

•Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

•Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

•Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

•Push starter button to start engine.

•Once the engine starts, immediately release starter button.

•As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to FULL and then slowly into the OFF position again.

•When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

Recoil Starter

•Rotate choke control to FULL choke position (cold engine start).

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models 60-3753-6 Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilitySetting up the Snow Thrower Setting UP Your Snow ThrowerBefore Assembly UnpackingChute Assembly all models For Models with 4 Way Chute Control BoxFinal Adjustments Chute Clean-out ToolSkid Shoe Primer Knowing Your Snow ThrowerThrottle Control Oil FillWay Chute Control optional Clean-Out ToolAuger Control Chute Directional Control optionalOperating Your Snow Thrower To Engage Augers Stopping The EngineTo Engage Drive For models with optional interlock mechanism onlyTo Throw Snow Operating TipsDrift Cutter Kit Chute Clean-Out ToolDrift Cutters on models so equipped Tire Chains on models so equippedShift Rod Adjustment Chute Bracket AdjustmentSkid Shoes Shave Plate and Skid Shoes EngineLubrication AugersAuger Belt Replacing BeltsDrive Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Yardworks 4 Year Limited Warranty Yardworks 4 Year Limited Warranty EnginesAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Manual Chute Control Styles H, K & L Part RÉF Pièce Description ANS Quatre DE Limitée Yardworks Garantie 9 Chapitre Pas couvre ne garantie CetteDépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Frottement de roue la de Caoutchouc en bague la de ChangementFigure la Voir .le-écartez et Patins et plate Lame Courroies les de RemplacementIllustrée po 30 de Tarière -21 Figure Lubrification MoteurPatins Tarière la de CommandeTransmission la de Commande Patins 19 FigureVitesses de levier du Tige Réglages 5 ChapitreGoulotte Coupe de Barres ’utilisation ConseilsPneu pour Chaînes Goulotte la de dégagement de OutilNeige la projeter Pour Tarière la embrayer PourTransmission la embrayer Pour Moteur du ArrêtTarières GoulotteLanceur à démarreur de Poignée Option en fonctions 4 à goulotte la de Commande Tarière la de CommandeOption en fonctions 2 à goulotte la de Commande ’entraînement de CommandeAmorceur ’obturateur de CommandeDépart de Volet Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» ’assemblage Avant Montage 2 ChapitreSouffleuse la de Assemblage Carton du DéballageResponsabilité Votre Remisage ET Entretien Préparation Formation5218-523 Chapitre3754-60 3753-60 Modèles

60-3753-6, 60-3754-4 specifications

The MTD 60-3753-6 and MTD 60-3754-4 are advanced mechanical components designed for a range of applications, primarily in landscaping, gardening, and outdoor power equipment. With an emphasis on durability and performance, these models are engineered to meet the demanding requirements of modern-day users.

One of the main features of the MTD 60-3753-6 is its robust construction. Built from high-quality materials, this component is designed to withstand the rigors of outdoor use, ensuring longevity and reliability. The 60-3754-4 complements this with its precision engineering, which reduces wear and tear, allowing for extended operational life. This focus on durability makes both components ideal for users who require consistent performance in challenging conditions.

In terms of technology, the MTD 60-3753-6 and 60-3754-4 incorporate innovative design elements that enhance their functionality. The use of advanced manufacturing techniques ensures that each component meets strict quality standards. Furthermore, these models are designed to provide easy installation and compatibility with a range of MTD equipment, making them user-friendly for technicians and DIY enthusiasts alike.

Another significant characteristic of these models is their versatility. The MTD 60-3753-6 is suitable for various applications, including tilling, mowing, and cultivating, while the 60-3754-4 can be used for tasks that require a flexible and durable component. This adaptability allows users to enjoy the benefits of these components across multiple equipment types, simplifying maintenance and part replacement.

Additionally, both models are designed with user comfort in mind. Ergonomic considerations have been incorporated, making these components easy to handle and operate. This focus on user experience is essential, especially for those using these components over extended periods.

In summary, the MTD 60-3753-6 and 60-3754-4 are exemplary models that showcase MTD's dedication to quality, innovation, and user satisfaction. Their robust construction, advanced technology, versatility, and ergonomic design make them indispensable for anyone seeking reliable mechanical components for their outdoor power equipment. Whether for professional landscaping or home gardening, these models provide the performance and durability that users can depend on.
Top Page Image Contents