MTD 60-3754-4, 60-3753-6 manual Friction Wheel Rubber

Page 18

•Push idler away from the chute and insert a Philips head screwdriver in the hole on the idler as shown in Figure 26. This will release tension on drive belt.

Engine

Auger Belt

 

Pulley

 

Drive Belt

Idler

Figure 26

•Pull drive belt out and away from the engine pulley to remove. See Figure 26.

•Tip the snow thrower up and forward, so that it rests on the housing. Remove two self-tapping screws from frame cover underneath the snow thrower and move the frame cover away. Refer to Figure 24.

•Back out the stop bolt to create sufficient gap between the friction wheel disc and the drive pulley. Pull the drive belt from around the drive pulley and clear it off the friction wheel disc. See Figure 27.

Drive

Friction

Belt

Wheel

 

Drive Pulley

Stop

Bolt

Figure 27

•Now moving to the other side of the snow thrower , slide the belt off the crankshaft.

•Replace with new belt, first sliding it through the crank shaft, then working it around the groove of the drive pulley and finally wrapping it around the engine pulley from where the old belt was removed. Once the belt is firmly placed on the pulleys, make sure to remove the screwdriver from the idler.

•Re-install auger belt on the engine pulley.

•Re-attach frame cover and put the equipment back to operating position. Re-attach belt cover with two self-tapping screws removed earlier.

Friction Wheel Rubber

•Check the rubber on the friction wheel after 25 hours of operation, and periodically thereafter. Replace the rubber if any signs of wear or cracking are found.

•Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

•Move shift lever to the R2 position.

•Tip the snow thrower so that it rests on the housing.

•Remove two self-tapping screws from frame cover underneath the snow thrower and move the frame cover away. See Figure 24.

•Remove the right-hand wheel by removing the screw and bell washer which secure it to the axle.

•Locate the hex shaft and snap ring on the right side of the snow thrower frame, about two inches from the wheel axle.

•Using a suitable tool, carefully remove the outer E- ring which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame.

•Slide the hex shaft downward and to the left while carefully un-meshing the lower gears on the hex shaft from the upper gears on the wheel axle. See Figure 28.

•Set the hex shaft’s gears aside.

•Carefully remove the inner E-ring from the hex shaft and slide the friction wheel assembly off the hex shaft.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft. Follow the steps above in reverse order to reassemble components. If you’re disassembling the friction wheel and replacing only the rubber ring, proceed as follows:

•Remove the four screws from the friction wheel assembly and remove the bonded friction wheel.

•Reassemble new bonded friction wheel rubber to the friction wheel assembly, turn each screw approximately 2 turns in order shown in Figure 29 until screws are tight. It is important for the rubber to be assembled symmetrically.

•Slide the friction wheel assembly back onto the hex shaft and follow the steps above in revers order to reassemble components.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Models 60-3753-6 Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilitySetting up the Snow Thrower Setting UP Your Snow ThrowerBefore Assembly UnpackingChute Assembly all models For Models with 4 Way Chute Control BoxChute Clean-out Tool Final AdjustmentsSkid Shoe Primer Knowing Your Snow ThrowerThrottle Control Oil FillWay Chute Control optional Clean-Out ToolAuger Control Chute Directional Control optionalOperating Your Snow Thrower To Engage Augers Stopping The EngineTo Engage Drive For models with optional interlock mechanism onlyTo Throw Snow Operating TipsDrift Cutter Kit Chute Clean-Out ToolDrift Cutters on models so equipped Tire Chains on models so equippedShift Rod Adjustment Chute Bracket AdjustmentSkid Shoes Shave Plate and Skid Shoes EngineLubrication AugersReplacing Belts Auger BeltDrive Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Yardworks 4 Year Limited Warranty Yardworks 4 Year Limited Warranty EnginesAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Manual Chute Control Styles H, K & L Part RÉF Pièce Description ANS Quatre DE Limitée Yardworks Garantie 9 Chapitre Pas couvre ne garantie CetteDépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Frottement de roue la de Caoutchouc en bague la de ChangementFigure la Voir .le-écartez et Courroies les de Remplacement Patins et plate LameIllustrée po 30 de Tarière -21 Figure Lubrification MoteurPatins Tarière la de CommandeTransmission la de Commande Patins 19 FigureRéglages 5 Chapitre Vitesses de levier du TigeGoulotte Coupe de Barres ’utilisation ConseilsPneu pour Chaînes Goulotte la de dégagement de OutilNeige la projeter Pour Tarière la embrayer PourTransmission la embrayer Pour Moteur du ArrêtGoulotte TarièresLanceur à démarreur de Poignée Option en fonctions 4 à goulotte la de Commande Tarière la de CommandeOption en fonctions 2 à goulotte la de Commande ’entraînement de Commande’obturateur de Commande AmorceurDépart de Volet Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» ’assemblage Avant Montage 2 ChapitreSouffleuse la de Assemblage Carton du DéballageResponsabilité Votre Remisage ET Entretien Préparation Formation5218-523 Chapitre3754-60 3753-60 Modèles

60-3753-6, 60-3754-4 specifications

The MTD 60-3753-6 and MTD 60-3754-4 are advanced mechanical components designed for a range of applications, primarily in landscaping, gardening, and outdoor power equipment. With an emphasis on durability and performance, these models are engineered to meet the demanding requirements of modern-day users.

One of the main features of the MTD 60-3753-6 is its robust construction. Built from high-quality materials, this component is designed to withstand the rigors of outdoor use, ensuring longevity and reliability. The 60-3754-4 complements this with its precision engineering, which reduces wear and tear, allowing for extended operational life. This focus on durability makes both components ideal for users who require consistent performance in challenging conditions.

In terms of technology, the MTD 60-3753-6 and 60-3754-4 incorporate innovative design elements that enhance their functionality. The use of advanced manufacturing techniques ensures that each component meets strict quality standards. Furthermore, these models are designed to provide easy installation and compatibility with a range of MTD equipment, making them user-friendly for technicians and DIY enthusiasts alike.

Another significant characteristic of these models is their versatility. The MTD 60-3753-6 is suitable for various applications, including tilling, mowing, and cultivating, while the 60-3754-4 can be used for tasks that require a flexible and durable component. This adaptability allows users to enjoy the benefits of these components across multiple equipment types, simplifying maintenance and part replacement.

Additionally, both models are designed with user comfort in mind. Ergonomic considerations have been incorporated, making these components easy to handle and operate. This focus on user experience is essential, especially for those using these components over extended periods.

In summary, the MTD 60-3753-6 and 60-3754-4 are exemplary models that showcase MTD's dedication to quality, innovation, and user satisfaction. Their robust construction, advanced technology, versatility, and ergonomic design make them indispensable for anyone seeking reliable mechanical components for their outdoor power equipment. Whether for professional landscaping or home gardening, these models provide the performance and durability that users can depend on.
Top Page Image Contents