MTD 60-3753-6, 60-3754-4 manual Chute Clean-out Tool, Final Adjustments, Skid Shoe

Page 7

Figure 8

Lamp Wire (optional)

1.Make sure the lamp wire is wrapped down the right handle as shown in Figure 9 .

2.Make sure the lamp wire is plugged into the alternator lead wire under the fuel tank. See Figure 9 inset.

Alternator Lead

Alternator

Lead

Lamp Wire

NOTE: Wheels are omitted from illustration for clarity.

Figure 9

Chute Clean-out Tool

1.The chute clean-out tool is fastened with a cable tie to the rear of the auger housing for shipping purposes. Cut the cable tie and remove the extension cord (if equipped) before operating the snow thrower.

Final Adjustments

After setting up your snow thrower, check the adjustments as instructed below and make any final adjustments necessary before operating the unit.

CAUTION: Failure to comply with these adjustment instructions may cause damage to the unit.

CAUTION: Prior to operating your snow thrower, refer to Auger Control Test on page 12. Read and follow all instructions carefully and perform all adjustments to verify your snow thrower is operating safely and properly.

Tire Pressure

Before operating, check tire pressure and reduce pressure in both tires to between 15 psi and 20 psi.

NOTE: If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

Skid Shoe

Locate the shave plate and the skid shoes in Figure

10.The space between this shave plate and the ground can be adjusted, refer to the Adjustment section of this manual.

IMPORTANT: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

7

Image 7
Contents Models 60-3753-6 Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageUnpacking Setting UP Your Snow ThrowerBefore Assembly Setting up the Snow ThrowerFor Models with 4 Way Chute Control Box Chute Assembly all modelsFinal Adjustments Chute Clean-out ToolSkid Shoe Oil Fill Knowing Your Snow ThrowerThrottle Control PrimerChute Directional Control optional Clean-Out ToolAuger Control Way Chute Control optionalOperating Your Snow Thrower For models with optional interlock mechanism only Stopping The EngineTo Engage Drive To Engage AugersOperating Tips To Throw SnowTire Chains on models so equipped Chute Clean-Out ToolDrift Cutters on models so equipped Drift Cutter KitChute Bracket Adjustment Shift Rod AdjustmentSkid Shoes Augers EngineLubrication Shave Plate and Skid ShoesAuger Belt Replacing BeltsDrive Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Yardworks 4 Year Limited Warranty Engines Yardworks 4 Year Limited WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Manual Chute Control Styles H, K & L Part RÉF Pièce Description Pas couvre ne garantie Cette ANS Quatre DE Limitée Yardworks Garantie 9 ChapitreDépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Caoutchouc en bague la de Changement Frottement de roue la deFigure la Voir .le-écartez et Patins et plate Lame Courroies les de RemplacementIllustrée po 30 de Tarière -21 Figure Moteur LubrificationPatins 19 Figure Tarière la de CommandeTransmission la de Commande PatinsVitesses de levier du Tige Réglages 5 ChapitreGoulotte Goulotte la de dégagement de Outil ’utilisation ConseilsPneu pour Chaînes Coupe de BarresTarière la embrayer Pour Neige la projeter PourMoteur du Arrêt Transmission la embrayer PourTarières GoulotteLanceur à démarreur de Poignée ’entraînement de Commande Tarière la de CommandeOption en fonctions 2 à goulotte la de Commande Option en fonctions 4 à goulotte la de CommandeAmorceur ’obturateur de CommandeDépart de Volet Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» Carton du Déballage Montage 2 ChapitreSouffleuse la de Assemblage ’assemblage AvantResponsabilité Votre Remisage ET Entretien Formation PréparationChapitre 5218-5233754-60 3753-60 Modèles

60-3753-6, 60-3754-4 specifications

The MTD 60-3753-6 and MTD 60-3754-4 are advanced mechanical components designed for a range of applications, primarily in landscaping, gardening, and outdoor power equipment. With an emphasis on durability and performance, these models are engineered to meet the demanding requirements of modern-day users.

One of the main features of the MTD 60-3753-6 is its robust construction. Built from high-quality materials, this component is designed to withstand the rigors of outdoor use, ensuring longevity and reliability. The 60-3754-4 complements this with its precision engineering, which reduces wear and tear, allowing for extended operational life. This focus on durability makes both components ideal for users who require consistent performance in challenging conditions.

In terms of technology, the MTD 60-3753-6 and 60-3754-4 incorporate innovative design elements that enhance their functionality. The use of advanced manufacturing techniques ensures that each component meets strict quality standards. Furthermore, these models are designed to provide easy installation and compatibility with a range of MTD equipment, making them user-friendly for technicians and DIY enthusiasts alike.

Another significant characteristic of these models is their versatility. The MTD 60-3753-6 is suitable for various applications, including tilling, mowing, and cultivating, while the 60-3754-4 can be used for tasks that require a flexible and durable component. This adaptability allows users to enjoy the benefits of these components across multiple equipment types, simplifying maintenance and part replacement.

Additionally, both models are designed with user comfort in mind. Ergonomic considerations have been incorporated, making these components easy to handle and operate. This focus on user experience is essential, especially for those using these components over extended periods.

In summary, the MTD 60-3753-6 and 60-3754-4 are exemplary models that showcase MTD's dedication to quality, innovation, and user satisfaction. Their robust construction, advanced technology, versatility, and ergonomic design make them indispensable for anyone seeking reliable mechanical components for their outdoor power equipment. Whether for professional landscaping or home gardening, these models provide the performance and durability that users can depend on.