MTD 60-3754-4, 60-3753-6 manual Shift Rod Adjustment, Chute Bracket Adjustment

Page 14

SECTION 5: MAKING ADJUSTMENTS

WARNING: Never attempt to make any adjustments while the engine is running, except where specified in operator’s manual.

Shift Rod Adjustment

If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures to the right and adjust the shift rod as follows:

Place the shift lever in the fastest forward

1 speed position. Remove the hairpin clip which secures the ferrule to the shift lever.

Thread the ferrule up or down the shift rod until

3 it aligns with the hole in the shift lever behind the handle panel. Resecure the ferrule with the

hairpin clip removed earlier.

Chute Assembly

The distance snow is thrown can be adjusted by changing the angle of the chute assembly. To do so, stop the engine by removing the ignition key and loosen the plastic wing knob found on the left side of the chute assembly. Pivot the chute upward or downward before re-tightening the wing knob. See Figure 16 .

13

2

2

Figure 13

Rotate the shift arm clockwise as far as it will go.

Figure 14

Figure 15

Figure 16

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so, loosen the two nuts which secure the chute bracket and reposition it slightly before retightening the nuts. See Figure 17 .

14

Image 14

Contents Models 60-3753-6 Table of Contents Important Safe Operation Practices TrainingMaintenance And Storage Your ResponsibilitySetting up the Snow Thrower Setting UP Your Snow ThrowerBefore Assembly UnpackingChute Assembly all models For Models with 4 Way Chute Control BoxSkid Shoe Chute Clean-out ToolFinal Adjustments Primer Knowing Your Snow ThrowerThrottle Control Oil FillWay Chute Control optional Clean-Out ToolAuger Control Chute Directional Control optionalOperating Your Snow Thrower To Engage Augers Stopping The Engine To Engage Drive For models with optional interlock mechanism onlyTo Throw Snow Operating TipsDrift Cutter Kit Chute Clean-Out ToolDrift Cutters on models so equipped Tire Chains on models so equippedShift Rod Adjustment Chute Bracket AdjustmentSkid Shoes Shave Plate and Skid Shoes EngineLubrication AugersDrive Belt Replacing BeltsAuger Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Yardworks 4 Year Limited Warranty Yardworks 4 Year Limited Warranty EnginesAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Manual Chute Control Styles H, K & L Part RÉF Pièce Description ANS Quatre DE Limitée Yardworks Garantie 9 Chapitre Pas couvre ne garantie CetteDépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Frottement de roue la de Caoutchouc en bague la de ChangementFigure la Voir .le-écartez et Illustrée po 30 de Tarière -21 Figure Courroies les de RemplacementPatins et plate Lame Lubrification MoteurPatins Tarière la de CommandeTransmission la de Commande Patins 19 FigureGoulotte Réglages 5 ChapitreVitesses de levier du Tige Coupe de Barres ’utilisation ConseilsPneu pour Chaînes Goulotte la de dégagement de OutilNeige la projeter Pour Tarière la embrayer PourTransmission la embrayer Pour Moteur du ArrêtLanceur à démarreur de Poignée GoulotteTarières Option en fonctions 4 à goulotte la de Commande Tarière la de CommandeOption en fonctions 2 à goulotte la de Commande ’entraînement de CommandeDépart de Volet ’obturateur de CommandeAmorceur Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» ’assemblage Avant Montage 2 ChapitreSouffleuse la de Assemblage Carton du DéballageResponsabilité Votre Remisage ET Entretien Préparation Formation5218-523 Chapitre3754-60 3753-60 Modèles