MTD 60-3753-6 manual Auger Control, Way Chute Control optional, Chute Directional Control optional

Page 9

Auger Control

The auger control is located on the left handle. Squeeze the auger control against the handle to engage the augers and start snow throwing action. Release to stop.

2 Way Chute Control (optional)

This two-way control lever is meant to control the

distance of snow discharge from the chute. Tilt the lever forward or rearward to adjust the distance snow will be

thrown.

Chute Directional Control (optional)

CHUTE DIRECTIONAL CONTROL

COMMANDE D'ORIENTATION DE LA GOULOTTE

Drive Control

The drive control is located on the right handle. Squeeze the drive control against the handle to engage the wheel drive. Release to stop.

4 Way Chute Control (optional)

This four-way control lever is meant to control the direction and distance of snow discharge from the

chute. Press the button on the knob and pivot it left or right to rotate the chute to the direction that snow will be

thrown. Tilt the lever forward or rearward to adjust the distance snow will be thrown.

Chute

Control Lever

The chute directional control is located on left side of the snow thrower.

To change the direction in which snow is thrown, turn chute directional control as follows:

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

Clean-Out Tool

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving

The tool is designed to clear a clogged chute assembly. Refer to Operating Your Snow Thrower section for more detailed information regarding the chute clean-out tool.

Skid Shoes

The space between the shave plate and the ground can be adjusted by moving the skid shoes.

For close snow removal and hard packed snow, place skid shoes in the lowest position. Use middle or high position when area to be cleared is uneven or gravel surface.

Make certain the entire bottom surface of the skid shoe is against the ground to avoid uneven wear on the slide shoes.

Recoil Starter Handle

The recoil starter handle is used to manually start the engine.

Electric Starter Button (If so equipped)

Pressing the electric starter button engages the engine’s electric starter when plugged into a 120V power source.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Models 60-3753-6 Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageBefore Assembly Setting UP Your Snow ThrowerSetting up the Snow Thrower UnpackingFor Models with 4 Way Chute Control Box Chute Assembly all modelsChute Clean-out Tool Final AdjustmentsSkid Shoe Throttle Control Knowing Your Snow ThrowerPrimer Oil FillAuger Control Clean-Out ToolWay Chute Control optional Chute Directional Control optionalOperating Your Snow Thrower To Engage Drive Stopping The EngineTo Engage Augers For models with optional interlock mechanism onlyOperating Tips To Throw SnowDrift Cutters on models so equipped Chute Clean-Out ToolDrift Cutter Kit Tire Chains on models so equippedChute Bracket Adjustment Shift Rod AdjustmentSkid Shoes Lubrication EngineShave Plate and Skid Shoes AugersReplacing Belts Auger BeltDrive Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Yardworks 4 Year Limited Warranty Engines Yardworks 4 Year Limited WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Manual Chute Control Styles H, K & L Part RÉF Pièce Description Pas couvre ne garantie Cette ANS Quatre DE Limitée Yardworks Garantie 9 ChapitreDépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Caoutchouc en bague la de Changement Frottement de roue la deFigure la Voir .le-écartez et Courroies les de Remplacement Patins et plate LameIllustrée po 30 de Tarière -21 Figure Moteur LubrificationTransmission la de Commande Tarière la de CommandePatins Patins 19 FigureRéglages 5 Chapitre Vitesses de levier du TigeGoulotte Pneu pour Chaînes ’utilisation ConseilsCoupe de Barres Goulotte la de dégagement de OutilTarière la embrayer Pour Neige la projeter PourMoteur du Arrêt Transmission la embrayer PourGoulotte TarièresLanceur à démarreur de Poignée Option en fonctions 2 à goulotte la de Commande Tarière la de CommandeOption en fonctions 4 à goulotte la de Commande ’entraînement de Commande’obturateur de Commande AmorceurDépart de Volet Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» Souffleuse la de Assemblage Montage 2 Chapitre’assemblage Avant Carton du DéballageResponsabilité Votre Remisage ET Entretien Formation PréparationChapitre 5218-5233754-60 3753-60 Modèles

60-3753-6, 60-3754-4 specifications

The MTD 60-3753-6 and MTD 60-3754-4 are advanced mechanical components designed for a range of applications, primarily in landscaping, gardening, and outdoor power equipment. With an emphasis on durability and performance, these models are engineered to meet the demanding requirements of modern-day users.

One of the main features of the MTD 60-3753-6 is its robust construction. Built from high-quality materials, this component is designed to withstand the rigors of outdoor use, ensuring longevity and reliability. The 60-3754-4 complements this with its precision engineering, which reduces wear and tear, allowing for extended operational life. This focus on durability makes both components ideal for users who require consistent performance in challenging conditions.

In terms of technology, the MTD 60-3753-6 and 60-3754-4 incorporate innovative design elements that enhance their functionality. The use of advanced manufacturing techniques ensures that each component meets strict quality standards. Furthermore, these models are designed to provide easy installation and compatibility with a range of MTD equipment, making them user-friendly for technicians and DIY enthusiasts alike.

Another significant characteristic of these models is their versatility. The MTD 60-3753-6 is suitable for various applications, including tilling, mowing, and cultivating, while the 60-3754-4 can be used for tasks that require a flexible and durable component. This adaptability allows users to enjoy the benefits of these components across multiple equipment types, simplifying maintenance and part replacement.

Additionally, both models are designed with user comfort in mind. Ergonomic considerations have been incorporated, making these components easy to handle and operate. This focus on user experience is essential, especially for those using these components over extended periods.

In summary, the MTD 60-3753-6 and 60-3754-4 are exemplary models that showcase MTD's dedication to quality, innovation, and user satisfaction. Their robust construction, advanced technology, versatility, and ergonomic design make them indispensable for anyone seeking reliable mechanical components for their outdoor power equipment. Whether for professional landscaping or home gardening, these models provide the performance and durability that users can depend on.
Top Page Image Contents