MTD 60-3753-6, 60-3754-4 manual Skid Shoes

Page 15

.

Figure 17

Drive Control

When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

Check the adjustment of the drive control as follows:

1.

With the drive control disengaged,

 

 

push the snow thrower gently

 

 

forward. The unit should roll freely.

 

2.

Engage the drive control and gently

 

 

attempt to push the snow thrower

Disengaged

 

forward. The wheels should not turn.

 

 

The unit should not roll freely.

 

3.With the drive control disengaged, move the shift lever back and forth between the R2 position and the F6 position several times. There should be no resistance in the shift lever.

If any of the above tests failed, the drive cable is in need of adjustment. refer to Figure 18 and proceed as follows:

•Loosen the hex jam nut on the auger control cable “Z” fitting and rotate the coupling end (without turning the cable) of the cable downward to provide more slack or upward to take up slack. See Figure 18 .

Auger Control

Refer to Auger Control Test on Page 12 to adjust the auger control.

Figure 18

Skid Shoes

NOTE: The space between the skid shoes and the ground can be adjusted. See Figure 19. For close snow removal, place skid shoe in the low position. Use middle or high position when area to be cleared is uneven.

NOTE: Some models are equipped with reversible skid shoes and may be turned over to increase their lifespan. See Figure 19.

CAUTION: Loose gravel can be picked up and thrown by the auger, causing injury to the operator and bystanders and/or damage to the snow thrower and surrounding property.

•Adjust skid shoes by loosening the four hex nuts (two on each side) and carriage bolts. Move skid shoes to desired position.

•Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes. Retighten nuts and bolts securely.

•Retighten the hex jam nut and repeat all three tests to verify proper adjustment has been achieved.

Standard

Reversible

Figure 19- Skid Shoes

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models 60-3753-6 Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance And StorageUnpacking Setting UP Your Snow ThrowerBefore Assembly Setting up the Snow ThrowerFor Models with 4 Way Chute Control Box Chute Assembly all modelsChute Clean-out Tool Final AdjustmentsSkid Shoe Oil Fill Knowing Your Snow ThrowerThrottle Control PrimerChute Directional Control optional Clean-Out ToolAuger Control Way Chute Control optionalOperating Your Snow Thrower For models with optional interlock mechanism only Stopping The EngineTo Engage Drive To Engage AugersOperating Tips To Throw SnowTire Chains on models so equipped Chute Clean-Out ToolDrift Cutters on models so equipped Drift Cutter KitChute Bracket Adjustment Shift Rod AdjustmentSkid Shoes Augers EngineLubrication Shave Plate and Skid ShoesReplacing Belts Auger BeltDrive Belt Friction Wheel Rubber OFF-SEASON Storage Trouble Shooting Yardworks 4 Year Limited Warranty Engines Yardworks 4 Year Limited WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Part RÉF Pièce Description Page Part RÉF Pièce Description For models with 22 auger housings Manual Chute Control Styles H, K & L Part RÉF Pièce Description Pas couvre ne garantie Cette ANS Quatre DE Limitée Yardworks Garantie 9 ChapitreDépannage DE Guide 8 Chapitre Saison Hors Remisage 7 Chapitre Caoutchouc en bague la de Changement Frottement de roue la deFigure la Voir .le-écartez et Courroies les de Remplacement Patins et plate LameIllustrée po 30 de Tarière -21 Figure Moteur LubrificationPatins 19 Figure Tarière la de CommandeTransmission la de Commande PatinsRéglages 5 Chapitre Vitesses de levier du TigeGoulotte Goulotte la de dégagement de Outil ’utilisation ConseilsPneu pour Chaînes Coupe de BarresTarière la embrayer Pour Neige la projeter PourMoteur du Arrêt Transmission la embrayer PourGoulotte TarièresLanceur à démarreur de Poignée ’entraînement de Commande Tarière la de CommandeOption en fonctions 2 à goulotte la de Commande Option en fonctions 4 à goulotte la de Commande’obturateur de Commande AmorceurDépart de Volet Neige la de dégagement de Outil «Réglage» chapitre le dans goulotte» Carton du Déballage Montage 2 ChapitreSouffleuse la de Assemblage ’assemblage AvantResponsabilité Votre Remisage ET Entretien Formation PréparationChapitre 5218-5233754-60 3753-60 Modèles

60-3753-6, 60-3754-4 specifications

The MTD 60-3753-6 and MTD 60-3754-4 are advanced mechanical components designed for a range of applications, primarily in landscaping, gardening, and outdoor power equipment. With an emphasis on durability and performance, these models are engineered to meet the demanding requirements of modern-day users.

One of the main features of the MTD 60-3753-6 is its robust construction. Built from high-quality materials, this component is designed to withstand the rigors of outdoor use, ensuring longevity and reliability. The 60-3754-4 complements this with its precision engineering, which reduces wear and tear, allowing for extended operational life. This focus on durability makes both components ideal for users who require consistent performance in challenging conditions.

In terms of technology, the MTD 60-3753-6 and 60-3754-4 incorporate innovative design elements that enhance their functionality. The use of advanced manufacturing techniques ensures that each component meets strict quality standards. Furthermore, these models are designed to provide easy installation and compatibility with a range of MTD equipment, making them user-friendly for technicians and DIY enthusiasts alike.

Another significant characteristic of these models is their versatility. The MTD 60-3753-6 is suitable for various applications, including tilling, mowing, and cultivating, while the 60-3754-4 can be used for tasks that require a flexible and durable component. This adaptability allows users to enjoy the benefits of these components across multiple equipment types, simplifying maintenance and part replacement.

Additionally, both models are designed with user comfort in mind. Ergonomic considerations have been incorporated, making these components easy to handle and operate. This focus on user experience is essential, especially for those using these components over extended periods.

In summary, the MTD 60-3753-6 and 60-3754-4 are exemplary models that showcase MTD's dedication to quality, innovation, and user satisfaction. Their robust construction, advanced technology, versatility, and ergonomic design make them indispensable for anyone seeking reliable mechanical components for their outdoor power equipment. Whether for professional landscaping or home gardening, these models provide the performance and durability that users can depend on.
Top Page Image Contents