Troy-Bilt 769-03253 To Engage Drive, To Engage Augers, Operating Tips, General Recommendations

Page 13

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150° F (65° C). Avoid these areas.

1.If possible, remove snow immediately after it falls.

2.Discharge snow downwind whenever possible.

3.Slightly overlap each previous path.

4.Set the skid shoes 1/4” below the shave plate for normal usage. Adjust them upward for hard-packed snow and downward when using on gravel or crushed rock.

General Recommendations

1.Always observe safety rules when performing any maintenance.

2.The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the snow thrower as instructed here.

3.Some adjustments will have to be made periodically to maintain your unit properly.

4.Periodically check all fasteners and make sure these

4

Operating

Your Snow

Thrower

WARNING

The muffler, engine and surrounding areas become hot and can cause a burn 150°F (65°C). Do not touch.

NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower opera-

IMPORTANT

NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Box 1386, KITCHENER, Ontario N2G 4J1 Two-Stage Snow Thrower769-03253 07/23/07 Finding and Recording Model Number Table of ContentsCustomer Support Result in personal injury. When you see this symbol, Heed Chute Clean-out ToolYour Responsibility Restrict the use Your Responsibility Safe Operation PracticesSafe Handling of Gasoline Allow machine to cool at least 5 minutes before storingAverage Useful Life Do not modify engineSetting Up Your Snow Thrower Attaching the Shift Rod Attaching the Chute AssemblyFinal Adjustments Clean-Out ToolDrift Cutters If Equipped Skid Shoes Check the adjustment of the auger control as followsTire Pressure Pneumatic Tires AugerKnow Your Snow Thrower Operating Your Snow ThrowerDrive Control / Auger Control Lock Chute Clean-Out ToolTwo-Way Chute Control Ignition KeyStopping The Engine Recoil StarterStarting The Engine Electric Starter on certain modelsTo Engage Drive Always observe safety rules when performing any maintenanceTo Engage Augers Operating TipsMaking AdjustmentsShift Rod Drive ControlChute Bracket Adjustment Chute AssemblySee Figure Adjust skid shoes as follows Auger ControlLubrication Maintaining Your Snow ThrowerAuger Belt Replacing BeltsRemove and replace auger belt inside belt keepers Drive BeltChanging Friction Wheel Rubber Friction wheel assembly and hold assembly in positionFriction Wheel Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Asphalt. Set to Torque to 20-30 in./lbsSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec Tec. LH 358 ccPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Frottement GarantieDépannage Solution Causes ProblèmePas Souffleuse Propre etCarburant le Videz Gaz Place en bougieEn bague la de Changement Frottement de roue caoutchouc’essieu de ’essenceClavette la ’entraînement CourroieRéduire la pour sens PoulieÉloignez Courroies les de RemplacementTarière la de d’entraînement Courroie Boulon l’autre retirezRoues LubrificationVitesse de ment MoteurRéglages Vitesses de levier du Tige Des l’entraînement de CommandeRoues ’utilisation Conseils Général d’ordre RecommandationsAnt Moteur du ArrêtModèles Certains sur électrique DémarreurGoulotte la de direction de Commande ’orientation CommandePhare Goulotte la de dégagement de Outil’obturateur de Commande Souffleuse la de CommandesAmorçeur Départ de VoletPneuma Bandages pneus des Pression Tiques’ajustement Vérifiez Goulotte la de dégagement de Outil Goulotte la de Installation Vitesses de levier du tige la de InstallationCette Remarque Les RemarqueMoyenne utile vie de Durée Responsabilité VotreGaz de émissions les concernant Avis Matériels’essence de Manipulation Responsabilité VotreSeulement De Outil Est goulotte la de dégagement de outil UnGoulotte la ed DégagementModèle de numéro le trouver Pour Vente-après ServiceMatières des Table Ca.troybilt.www Phases deux neige à Souffleuse07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents