Troy-Bilt 769-03253 warranty Skid Shoes, Tire Pressure Pneumatic Tires, Auger Control

Page 9

A B

Drive

Auger

Figure 11

•Loosen the Nylock nut on the drive control cable and unthread the cable one full turn. See Figure 13.

•Recheck adjustment.

•Retighten the Nylock nut to secure the cable when correct adjustment is reached.

NOTE: For more details, refer to Drive Control Adjust- ment in the Adjustment Section of this manual.

Auger Control

Check the adjustment of the auger control as follows:

•When the auger control is released and in the disengaged “up” position (see Figure 11B), the cable should have very little slack, but should NOT be tight. See Figure 12.

WARNING:Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compromise the safety of the snow thrower.

•In a well-ventilated area, start the snow thrower engine as instructed on page 12. Make sure the throttle is set in the fast position.

•While standing in the operator’s position (behind the snow thrower) engage the auger.

•Allow the auger to remain engaged for approximately ten seconds before releasing the auger control. Repeat this several times.

•With the engine running in the fast position and the auger control lever in the disengaged “up” position, walk to the front of the machine.

•Confirm that the auger has completely stopped rotating and shows no signs of motion.

IMPORTANT: If the auger shows any signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for all moving parts to stop before readjusting the auger control cable.

•To readjust the control cable, unhook the spring (found on the end of the auger cable) from the auger actuator bracket. See Figure 12.

•Push the cable coupler through the end of the spring to expose the lock nut. See Figure 13.

Figure 12

Figure 13

•Thread the Nylock nut outward (down the coupler) three full turns to provide more slack in the cable and reattach the spring to the bracket.

•Repeat auger control test to verify for proper adjustment. Repeat previous steps to adjust more, if necessary.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary.

3

Setting Up

Your Snow

Thrower

WARNING

Never use your hands to clean snow and ice from the chute assembly or auger housing.

IMPORTANT

If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Two-Stage Snow Thrower Box 1386, KITCHENER, Ontario N2G 4J1769-03253 07/23/07 Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Result in personal injury. When you see this symbol, HeedYour Responsibility Restrict the use Your Responsibility Safe Operation PracticesSafe Handling of Gasoline Allow machine to cool at least 5 minutes before storingAverage Useful Life Do not modify engineSetting Up Your Snow Thrower Attaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Skid Shoes Check the adjustment of the auger control as followsTire Pressure Pneumatic Tires AugerKnow Your Snow Thrower Operating Your Snow ThrowerDrive Control / Auger Control Lock Chute Clean-Out ToolTwo-Way Chute Control Ignition KeyStopping The Engine Recoil StarterStarting The Engine Electric Starter on certain modelsTo Engage Drive Always observe safety rules when performing any maintenanceTo Engage Augers Operating TipsMaking AdjustmentsShift Rod Drive ControlChute Bracket Adjustment Chute AssemblySee Figure Adjust skid shoes as follows Auger ControlLubrication Maintaining Your Snow ThrowerAuger Belt Replacing BeltsRemove and replace auger belt inside belt keepers Drive BeltFriction wheel assembly and hold assembly in position Changing Friction Wheel RubberFriction Wheel Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Asphalt. Set to Torque to 20-30 in./lbsSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec Tec. LH 358 ccPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Frottement GarantieSolution Causes Problème DépannagePas Souffleuse Propre etCarburant le Videz Gaz Place en bougieEn bague la de Changement Frottement de roue caoutchouc’essieu de ’essenceClavette la ’entraînement CourroieRéduire la pour sens PoulieÉloignez Courroies les de RemplacementTarière la de d’entraînement Courroie Boulon l’autre retirezRoues LubrificationVitesse de ment MoteurRéglages Des l’entraînement de Commande Vitesses de levier du TigeRoues ’utilisation Conseils Général d’ordre RecommandationsAnt Moteur du ArrêtModèles Certains sur électrique DémarreurGoulotte la de direction de Commande ’orientation CommandePhare Goulotte la de dégagement de Outil’obturateur de Commande Souffleuse la de CommandesAmorçeur Départ de VoletTiques Pneuma Bandages pneus des Pression’ajustement Vérifiez Goulotte la de dégagement de Outil Goulotte la de Installation Vitesses de levier du tige la de InstallationCette Remarque Les RemarqueMoyenne utile vie de Durée Responsabilité VotreGaz de émissions les concernant Avis MatérielsResponsabilité Votre ’essence de ManipulationSeulement De Outil Est goulotte la de dégagement de outil UnGoulotte la ed DégagementVente-après Service Modèle de numéro le trouver PourMatières des Table Phases deux neige à Souffleuse Ca.troybilt.www07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents