Troy-Bilt 769-03253 warranty Drive Belt, Remove and replace auger belt inside belt keepers

Page 18

6

Maintaining

Your Snow

Thrower

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

IMPORTANT

Refer to the Final Adjustment section of the Set-Up instructions after replacing drive and auger belts.

Figure 28

9.Place a block of wood underneath the auger housing as shown in Figure 29 and separate auger housing from the frame by tilting the housing forward and pulling up the handles.

10.a. Using a 1/2” wrench, remove the hex screw and washer from the center of the pulley on the auger housing. See Figure 30.

b.Lift the brake bracket assembly out of the pulley groove

c.Remove the pulley.

11.Remove and replace auger belt inside belt keepers.

12.Apply Loctite 262 to the threads of the hex screw used for mounting the auger pulley.

13.Reassemble pulley to auger housing with hex screw and washer. Torque hex screw 250-325 in. lbs.

NOTE: Make sure the brake puck is seated in the pulley groove.

If also replacing the drive belt, proceed to the “Drive Belt” instruction. If not, reassemble by performing the previous steps in the opposite order and manner of removal.

Proper Adjustment: With the auger clutch lever in the disengaged position, the top surface of the new belt should be even with the outside diameter of the pulley.

1.To adjust, disconnect ferrule from brake bracket as- sembly and thread ferrule in (towards idler) to increase tension on belt, and out to decrease tension.

NOTE: The brake puck must always be firmly seated in the pulley groove when auger control is disengaged.

Drive Belt

1.Pull the idler pulley away from the backside of the drive belt to relieve the tension and slide the drive belt off the idler pulley. See Figure 31.

2.Remove the belt from the bottom drive pulley and the engine pulley.

Figure 29

B

C

A

 

Figure 30

1

3

2

Figure 31

3.Install the new belt on the pulleys in the reverse order and re-tension with the idler pulley.

Reassemble your unit by performing the previous steps in the opposite order.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Two-Stage Snow Thrower Box 1386, KITCHENER, Ontario N2G 4J1769-03253 07/23/07 Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Result in personal injury. When you see this symbol, HeedYour Responsibility Restrict the use Safe Handling of Gasoline Safe Operation PracticesYour Responsibility Allow machine to cool at least 5 minutes before storingDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Attaching the Chute Assembly Attaching the Shift RodClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Tire Pressure Pneumatic Tires Check the adjustment of the auger control as followsSkid Shoes AugerOperating Your Snow Thrower Know Your Snow ThrowerTwo-Way Chute Control Chute Clean-Out ToolDrive Control / Auger Control Lock Ignition KeyStarting The Engine Recoil StarterStopping The Engine Electric Starter on certain modelsTo Engage Augers Always observe safety rules when performing any maintenanceTo Engage Drive Operating TipsShift Rod AdjustmentsMaking Drive ControlSee Figure Adjust skid shoes as follows Chute AssemblyChute Bracket Adjustment Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger BeltDrive Belt Remove and replace auger belt inside belt keepersFriction wheel assembly and hold assembly in position Changing Friction Wheel RubberFriction Wheel Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06For parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 20-30 in./lbs Asphalt. Set toSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec. LH 358 cc TecPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Garantie FrottementSolution Causes Problème DépannagePas Carburant le Videz Gaz Propre etSouffleuse Place en bougie’essieu de Frottement de roue caoutchoucEn bague la de Changement ’essenceRéduire la pour sens ’entraînement CourroieClavette la PoulieTarière la de d’entraînement Courroie Courroies les de RemplacementÉloignez Boulon l’autre retirezVitesse de ment LubrificationRoues MoteurRéglages Des l’entraînement de Commande Vitesses de levier du TigeRoues Général d’ordre Recommandations ’utilisation ConseilsModèles Moteur du ArrêtAnt Certains sur électrique DémarreurPhare ’orientation CommandeGoulotte la de direction de Commande Goulotte la de dégagement de OutilAmorçeur Souffleuse la de Commandes’obturateur de Commande Départ de VoletTiques Pneuma Bandages pneus des Pression’ajustement Vérifiez Goulotte la de dégagement de Outil Vitesses de levier du tige la de Installation Goulotte la de InstallationLes Remarque Cette RemarqueGaz de émissions les concernant Avis Responsabilité VotreMoyenne utile vie de Durée MatérielsResponsabilité Votre ’essence de ManipulationSeulement Goulotte la ed Est goulotte la de dégagement de outil UnDe Outil DégagementVente-après Service Modèle de numéro le trouver PourMatières des Table Phases deux neige à Souffleuse Ca.troybilt.www07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents