Troy-Bilt 769-03253 warranty Maintaining Your Snow Thrower, Lubrication

Page 16

6

Friction

Gear (Hex) Shaft

Lubrication

Drive and Shifting Mechanism

At least once a season or after every 25 hours of opera- tion, remove rear cover. Lubricate any chains, sprockets, gears, bearings, shafts, and the shifting mechanism at least once a season. Use engine oil or a spray lubricant.

Maintaining

Your Snow

Thrower

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

IMPORTANT

Avoid oil spillage on rubber friction wheel and aluminum drive plate.

Wheel

Drive

Plate

Figure 20

Shear Pin

Vent Plug

Grease

 

 

Fitting (optional)

Auger Shaft

 

Cotter Pin

Spacers

Bearing

Figure 21

Figure 22

Engine

Refer to the separate engine manual packed with your unit for all engine maintenance and lubrication instruc- tions.

Refer to Figure 20.

IMPORTANT: Keep all grease and oil off the rubber friction wheel and drive plate.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 21.

Augers

•The augers are secured to the spiral shaft with shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. See Figure 21.

•If the augers will not turn, check to see if the pins have sheared. One set of replacement shear pins has been provided with the snow thrower. When replacing pins, spray an oil lubricant into shaft before inserting new pins.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1.Remove the carriage bolts (and washers if equipped)and hex flange nuts which secure the skid shoes to the snow thrower.

2.Reassemble new skid shoes with previously removed hardware. Refer to Figure 22.

To remove shave plate:

1.Remove the carriage bolts and hex nuts which attach it and the skid shoes to the snow thrower housing.

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Box 1386, KITCHENER, Ontario N2G 4J1 Two-Stage Snow Thrower769-03253 07/23/07 Finding and Recording Model Number Table of ContentsCustomer Support Result in personal injury. When you see this symbol, Heed Chute Clean-out ToolYour Responsibility Restrict the use Safe Operation Practices Your ResponsibilitySafe Handling of Gasoline Allow machine to cool at least 5 minutes before storingDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Attaching the Chute Assembly Attaching the Shift RodFinal Adjustments Clean-Out ToolDrift Cutters If Equipped Check the adjustment of the auger control as follows Skid ShoesTire Pressure Pneumatic Tires AugerOperating Your Snow Thrower Know Your Snow ThrowerChute Clean-Out Tool Drive Control / Auger Control LockTwo-Way Chute Control Ignition KeyRecoil Starter Stopping The EngineStarting The Engine Electric Starter on certain modelsAlways observe safety rules when performing any maintenance To Engage DriveTo Engage Augers Operating TipsAdjustments MakingShift Rod Drive ControlChute Assembly Chute Bracket AdjustmentSee Figure Adjust skid shoes as follows Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger BeltDrive Belt Remove and replace auger belt inside belt keepersChanging Friction Wheel Rubber Friction wheel assembly and hold assembly in positionFriction Wheel Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06For parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 20-30 in./lbs Asphalt. Set toSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec. LH 358 cc TecPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Garantie FrottementDépannage Solution Causes ProblèmePas Propre et SouffleuseCarburant le Videz Gaz Place en bougieFrottement de roue caoutchouc En bague la de Changement’essieu de ’essence’entraînement Courroie Clavette laRéduire la pour sens PoulieCourroies les de Remplacement ÉloignezTarière la de d’entraînement Courroie Boulon l’autre retirezLubrification RouesVitesse de ment MoteurRéglages Vitesses de levier du Tige Des l’entraînement de CommandeRoues Général d’ordre Recommandations ’utilisation ConseilsMoteur du Arrêt AntModèles Certains sur électrique Démarreur’orientation Commande Goulotte la de direction de CommandePhare Goulotte la de dégagement de OutilSouffleuse la de Commandes ’obturateur de CommandeAmorçeur Départ de VoletPneuma Bandages pneus des Pression Tiques’ajustement Vérifiez Goulotte la de dégagement de Outil Vitesses de levier du tige la de Installation Goulotte la de InstallationLes Remarque Cette RemarqueResponsabilité Votre Moyenne utile vie de DuréeGaz de émissions les concernant Avis Matériels’essence de Manipulation Responsabilité VotreSeulement Est goulotte la de dégagement de outil Un De OutilGoulotte la ed DégagementModèle de numéro le trouver Pour Vente-après ServiceMatières des Table Ca.troybilt.www Phases deux neige à Souffleuse07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents