Troy-Bilt 769-03253 warranty Attaching the Chute Assembly, Attaching the Shift Rod

Page 7

Figure 4

Attaching the Chute Assembly

•Remove locknuts and screws securing one of the flange keepers to the chute assembly. See Figure 4.

•Loosen but do not remove the locknuts and screws on the other two flange keepers.

•Slide chute assembly over chute opening, making sure the flange keepers are beneath lip of chute adapter. The notches should engage with the spiral end of the chute crank. See Figure 5.

•Secure flange keeper, locknuts and screws previously removed. Tighten all flange keepers and hardware with two 7/16” wrenches. Do not over tighten.

NOTE: If necessary the chute crank support bracket can be adjusted so the spiral on the chute crank fully engages the teeth on the chute assembly. Refer to the Adjustment Section.

Attaching the Shift Rod

•Align the upper and lower shift rods, then slide the shift rod connector down over the end of the lower shift rod. Tap the connector until the lower rod is completely through the connector. See Figure 6.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to change speeds or direction.

NOTE: If the full range of speeds (forward and reverse) cannot be achieved, refer to the Adjustment Section.

•Normally the cable ties holding the steering cables against the handle are loosely installed on each side of the lower handle at the factory. Pull the cable ties tight to secure. Cut the excess from the ends of cable ties.

•If not already attached, slip the cables that run from the handle panel to the discharge chute into the cable guide located on top of the engine. See Figure 7.

•Wrap the wire from the head lamp down the right handle until the wire can be plugged into the alternator lead wire under the fuel tank. See Figure 8.

3

Setting Up

Your Snow

Thrower

Figure 5

WARNING

Prior to operating your snow thrower, refer to Auger Control on page 9. Read and follow all instructions carefully and perform all adjustments to verify your unit is operating safely and properly.

Figure 6

Figure 7



Page 6 Page 8
Image 7
Page 6 Page 8
Contents Box 1386, KITCHENER, Ontario N2G 4J1 Two-Stage Snow Thrower769-03253 07/23/07 Finding and Recording Model Number Table of ContentsCustomer Support Result in personal injury. When you see this symbol, Heed Chute Clean-out ToolYour Responsibility Restrict the use Allow machine to cool at least 5 minutes before storing Safe Operation PracticesYour Responsibility Safe Handling of GasolineAverage Useful Life Do not modify engineSetting Up Your Snow Thrower Attaching the Shift Rod Attaching the Chute AssemblyFinal Adjustments Clean-Out ToolDrift Cutters If Equipped Auger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow ThrowerIgnition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlElectric Starter on certain models Recoil StarterStopping The Engine Starting The EngineOperating Tips Always observe safety rules when performing any maintenanceTo Engage Drive To Engage AugersDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerAuger Belt Replacing BeltsRemove and replace auger belt inside belt keepers Drive BeltChanging Friction Wheel Rubber Friction wheel assembly and hold assembly in positionFriction Wheel Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Adressez-vous au «Service après-vente» Parts List Pièces DétachéesLa page 2 pour ce qui concerne les pièces et/ou accessoires Asphalt. Set to Torque to 20-30 in./lbsSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec Tec. LH 358 ccPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Frottement GarantieDépannage Solution Causes ProblèmePas Place en bougie Propre etSouffleuse Carburant le Videz Gaz’essence Frottement de roue caoutchoucEn bague la de Changement ’essieu dePoulie ’entraînement CourroieClavette la Réduire la pour sensBoulon l’autre retirez Courroies les de RemplacementÉloignez Tarière la de d’entraînement CourroieMoteur LubrificationRoues Vitesse de mentRéglages Vitesses de levier du Tige Des l’entraînement de CommandeRoues ’utilisation Conseils Général d’ordre RecommandationsCertains sur électrique Démarreur Moteur du ArrêtAnt ModèlesGoulotte la de dégagement de Outil ’orientation CommandeGoulotte la de direction de Commande PhareDépart de Volet Souffleuse la de Commandes’obturateur de Commande AmorçeurPneuma Bandages pneus des Pression Tiques’ajustement Vérifiez Goulotte la de dégagement de Outil Goulotte la de Installation Vitesses de levier du tige la de InstallationCette Remarque Les RemarqueMatériels Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant Avis’essence de Manipulation Responsabilité VotreSeulement Dégagement Est goulotte la de dégagement de outil UnDe Outil Goulotte la edModèle de numéro le trouver Pour Vente-après ServiceMatières des Table Ca.troybilt.www Phases deux neige à Souffleuse07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents