Troy-Bilt 769-03253 warranty Setting Up Your Snow Thrower

Page 6

3

Setting Up

Your Snow

Thrower

NOTE: This Operator’s Manual covers several models. Snowthrower featrues vary by model. Not all features refer- enced in this manual are applicable to all snowthrower models.

NOTE: References to right or left side of the snow thrower are deter- mined from behind the unit in the operating position.

NOTE: Replacement auger shear pins and cotter pins are provided for your convenience. Store these safely until needed.

Figure 1

Figure 2

a

b

Figure 3

IMPORTANT: The snow thrower is shipped with oil and WITHOUT GASOLINE. After assembly, refer to separate engine manual for proper fuel and engine oil recom- mendations.

Loose Parts

•The augers are secured to the auger shaft with shear pins and bow tie cotter pins. If you hit a foreign object or ice jam, the snow thrower is designed so that the pins may shear. Replacement shear pins and cotter pins are provided for your convenience. Store these safely until needed.

Items Required For Assembly

Pair of pliers

7/16” Wrenches or adjustables

Fresh gasoline

 

Before Assembly

•Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

•Reference to the right hand or left hand side of machine are observed from the operating position.

Assembling Handle

•Look at the lower rear of the snow thrower frame to be sure the spring (found at the end of each cable) is attached to its actuator bracket.

•Remove the lower handle knobs, washers and carriage bolts from each side of the lower handle. See Figure 2.

•Raise the upper handle assembly until it locks over the lower handle. See Figure 1.

•Secure the upper handle and lower handle with the handle knobs and carriage bolts previously removed.

•Tighten the handle knobs already in place on the upper holes and secure the handles firmly.

Attaching Chute Crank

•Remove the hairpin clip from the upper chute crank and slide the upper chute crank into the lower chute crank. A pair of pliers may help in this job. See Figure 3.

a.Align the two holes on both chute cranks. See Figure 3.

b.Secure with the hairpin clip removed earlier.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Two-Stage Snow Thrower Box 1386, KITCHENER, Ontario N2G 4J1769-03253 07/23/07 Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Result in personal injury. When you see this symbol, HeedYour Responsibility Restrict the use Safe Handling of Gasoline Safe Operation PracticesYour Responsibility Allow machine to cool at least 5 minutes before storingDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Attaching the Chute Assembly Attaching the Shift RodClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Tire Pressure Pneumatic Tires Check the adjustment of the auger control as followsSkid Shoes AugerOperating Your Snow Thrower Know Your Snow ThrowerTwo-Way Chute Control Chute Clean-Out ToolDrive Control / Auger Control Lock Ignition KeyStarting The Engine Recoil StarterStopping The Engine Electric Starter on certain modelsTo Engage Augers Always observe safety rules when performing any maintenanceTo Engage Drive Operating TipsShift Rod AdjustmentsMaking Drive ControlSee Figure Adjust skid shoes as follows Chute AssemblyChute Bracket Adjustment Auger ControlMaintaining Your Snow Thrower LubricationReplacing Belts Auger BeltDrive Belt Remove and replace auger belt inside belt keepersFriction wheel assembly and hold assembly in position Changing Friction Wheel RubberFriction Wheel Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting Problem Cause RemedyWarranty 12.08.06For parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Torque to 20-30 in./lbs Asphalt. Set toSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec. LH 358 cc TecPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Garantie FrottementSolution Causes Problème DépannagePas Carburant le Videz Gaz Propre etSouffleuse Place en bougie’essieu de Frottement de roue caoutchoucEn bague la de Changement ’essenceRéduire la pour sens ’entraînement CourroieClavette la PoulieTarière la de d’entraînement Courroie Courroies les de RemplacementÉloignez Boulon l’autre retirezVitesse de ment LubrificationRoues MoteurRéglages Des l’entraînement de Commande Vitesses de levier du TigeRoues Général d’ordre Recommandations ’utilisation ConseilsModèles Moteur du ArrêtAnt Certains sur électrique DémarreurPhare ’orientation CommandeGoulotte la de direction de Commande Goulotte la de dégagement de OutilAmorçeur Souffleuse la de Commandes’obturateur de Commande Départ de VoletTiques Pneuma Bandages pneus des Pression’ajustement Vérifiez Goulotte la de dégagement de Outil Vitesses de levier du tige la de Installation Goulotte la de InstallationLes Remarque Cette RemarqueGaz de émissions les concernant Avis Responsabilité VotreMoyenne utile vie de Durée MatérielsResponsabilité Votre ’essence de ManipulationSeulement Goulotte la ed Est goulotte la de dégagement de outil UnDe Outil DégagementVente-après Service Modèle de numéro le trouver PourMatières des Table Phases deux neige à Souffleuse Ca.troybilt.www07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents