Troy-Bilt 769-03253 Auger Control, Chute Assembly, Chute Bracket Adjustment, Retighten the nuts

Page 15

Skid Shoes

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position.

See Figure 18.

Adjust skid shoes as follows:

1.Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

2.Raise or lower the skid shoe to desired position.

3.Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear.

4. Repeat on the other side of the snow thrower.

Auger Control

Refer to instructions on page 9 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to page 9 for instructions.

The remote chute control cables have been pre-adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so:

1.Loosen the two nuts which secure the chute bracket and reposition it slightly. See Figure 19.

2.Retighten the nuts.

Figure 18

Figure 19

5

Making

Adjustments

IMPORTANT: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the high- est position for maximum clearance between the ground and the shave plate.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Two-Stage Snow Thrower Box 1386, KITCHENER, Ontario N2G 4J1769-03253 07/23/07 Table of Contents Finding and Recording Model NumberCustomer Support Chute Clean-out Tool Result in personal injury. When you see this symbol, HeedYour Responsibility Restrict the use Allow machine to cool at least 5 minutes before storing Safe Operation PracticesYour Responsibility Safe Handling of GasolineAverage Useful Life Do not modify engineSetting Up Your Snow Thrower Attaching the Shift Rod Attaching the Chute AssemblyClean-Out Tool Final AdjustmentsDrift Cutters If Equipped Auger Check the adjustment of the auger control as followsSkid Shoes Tire Pressure Pneumatic TiresKnow Your Snow Thrower Operating Your Snow ThrowerIgnition Key Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlElectric Starter on certain models Recoil StarterStopping The Engine Starting The EngineOperating Tips Always observe safety rules when performing any maintenanceTo Engage Drive To Engage AugersDrive Control AdjustmentsMaking Shift RodAuger Control Chute AssemblyChute Bracket Adjustment See Figure Adjust skid shoes as followsLubrication Maintaining Your Snow ThrowerAuger Belt Replacing BeltsRemove and replace auger belt inside belt keepers Drive BeltFriction wheel assembly and hold assembly in position Changing Friction Wheel RubberFriction Wheel Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy Trouble Shooting12.08.06 WarrantyFor parts and/or accessories refer to customer support on 6919 Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Asphalt. Set to Torque to 20-30 in./lbsSee chart on next page./ Voir le tableau à la page prochaîne Part Description RÉF Pièce Style Tec Tec. LH 358 ccPart Description RÉF Pièce Part Description RÉF Pièce For parts and/or accessories refer to customer support on Page Frottement GarantieSolution Causes Problème DépannagePas Place en bougie Propre etSouffleuse Carburant le Videz Gaz’essence Frottement de roue caoutchoucEn bague la de Changement ’essieu dePoulie ’entraînement CourroieClavette la Réduire la pour sensBoulon l’autre retirez Courroies les de RemplacementÉloignez Tarière la de d’entraînement CourroieMoteur LubrificationRoues Vitesse de mentRéglages Des l’entraînement de Commande Vitesses de levier du TigeRoues ’utilisation Conseils Général d’ordre RecommandationsCertains sur électrique Démarreur Moteur du ArrêtAnt ModèlesGoulotte la de dégagement de Outil ’orientation CommandeGoulotte la de direction de Commande PhareDépart de Volet Souffleuse la de Commandes’obturateur de Commande AmorçeurTiques Pneuma Bandages pneus des Pression’ajustement Vérifiez Goulotte la de dégagement de Outil Goulotte la de Installation Vitesses de levier du tige la de InstallationCette Remarque Les RemarqueMatériels Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisResponsabilité Votre ’essence de ManipulationSeulement Dégagement Est goulotte la de dégagement de outil UnDe Outil Goulotte la edVente-après Service Modèle de numéro le trouver PourMatières des Table Phases deux neige à Souffleuse Ca.troybilt.www07/23/07
Related manuals
Manual 23 pages 63.44 Kb

769-03253 specifications

The Troy-Bilt 769-03253 is a standout model in the world of outdoor power equipment, specifically tailored for those looking for a robust and efficient gardening solution. This product, often recognized for its reliability and user-friendly design, is ideal for homeowners seeking to maintain their yards with minimal effort.

One of the most notable features of the Troy-Bilt 769-03253 is its powerful 270cc engine, which provides ample power for various yard tasks. This engine delivers strong performance, making it capable of handling tougher jobs like tilling hard, compacted soil or breaking new ground. The engine is designed for easy starting, thanks to its innovative recoil start system, making it accessible to users of all skill levels.

The tilling width of the Troy-Bilt 769-03253 is impressive at 18 inches, allowing users to cover a larger area in less time. This feature is particularly beneficial for larger gardens or landscaping projects. Additionally, the tiller is equipped with a depth adjuster, enabling precise control over how deep you can till into the soil, which is essential for different planting requirements.

Another key attribute of this tiller is its counter-rotating tines. This technology allows for better soil mixing and improved aeration, promoting healthier soil and more robust plant growth. The tines are made from durable materials, ensuring longevity even when used in tougher ground conditions. They are also designed for easy replacement, which adds to the overall convenience.

Ergonomics play a significant role in the design of the Troy-Bilt 769-03253, featuring adjustable handles that accommodate users of various heights. This ensures comfort during extended use, reducing fatigue and enhancing overall productivity. Furthermore, the tiller is designed for optimal stability, with a balanced build that prevents it from tipping during operation.

The Troy-Bilt 769-03253 also incorporates safety features such as an automatic clutch that ensures the tiller comes to a stop when not in use, helping to prevent accidents. With its combination of power, durability, and ease of use, the Troy-Bilt 769-03253 is a top choice for anyone looking to enhance their gardening and landscaping projects, making it a valuable addition to any homeowner's outdoor toolkit.
Top Page Image Contents