Troy-Bilt 1400 warranty Maintenance & Adjustments, Off-Season Storage, Resetting Circuit Breaker

Page 13

Maintenance & Adjustments

6

Resetting Circuit Breaker

This snow thrower is equipped with a circuit breaker to prevent overheating damage to the motor.

If the circuit breaker reset button pops out:

1.Release the motor control lever and do NOT restart the snow thrower for at least one minute, allowing the electric motor time to cool.

2.Press the circuit breaker reset button (located on the switch assembly) inward to reset. See Figure 6-1.

Maintenance

Lubrication

Lubricate the pivot points on the motor control lever with a light oil once every season and before the snow thrower is put into storage at the end of the season.

Off-Season Storage

If the snow thrower will not be used for 30 days or longer, follow the instructions below.

•Clean and lubricate snow thrower thoroughly as described in the lubrication instructions.

•We do not recommend the use of a pressure washer or garden hose to clean your unit.

•Make certain the power supply is disconnected.

•Store snow thrower in a dry, clean area. Do not store next to corrosive materials, such as fertilizer.

•Wipe extension cord to remove any foreign substance such as oil or stains. Replace extension cord if cut or damaged in any way.

•Wind cord in a series of equal loops on each side of your hand to prevent snarling.

Figure 6-1

14

Image 13

Contents Operator’s Manual To The Owner Table of ContentsThank You Record Product InformationDouble Insulated Snow Thrower Important Safe Operation PracticesBefore Operating While Operating Be sure to secure the unit while transporting Other Safety WarningsSymbol Safety SymbolsContents of Carton Assembly & Set-UpHandle Assembly Tools Required for AssemblyChute Assembly Front Cover Screw Chute AssemblyCarriage Bolt Handle Knobs Cable Guide Motor CordSide View Connecting Extension CordControls & Features Operation Adjusting the Chute AssemblyStarting Motor Stopping the MotorTo clear the chute Clearing a Clogged Discharge ChuteMaintenance Maintenance & AdjustmentsResetting Circuit Breaker Off-Season StorageReplacing Skid Plate ServiceReplacing Auger Belt Side ViewReplacing Wheels Replacing Cogged Belt Replacing Auger PaddlesPull the belt off Pulley B Replace in the opposite order Problem Cause Remedy TroubleshootingComponent Part Number and Description Replacement PartsAuger Belt Rubber AugerCanada U.S.AGDOC-100166 REV. a Manual del operador Gracias Al propietarioÍndice Registro de información de productoMáquina quitanieve con aislamiento doble Medidas importantes de seguridadAntes de la operación Tenga cuidado para evitar resbalar o caerse100 150 Mientras está en funcionamientoCable del Camine, nunca corraCompruebe que haya sujetado la unidad durante el transporte Otras advertencias de seguridadAmputación de manos o pies Símbolos de seguridadContenido de la caja de cartón Montaje y ConfiguraciónHerramientas necesarias para el montaje Cómo desembalar la unidadMontaje del canal Cubierta Delantera Tornillo Montaje del canalConexión del prolongador Controles y Características Botón de reposición del disyuntor Canal de descargaArranque del motor FuncionamientoParada del Motor La Participación de la UnidadEliminación de un Tubo de Descarga Obstruida Ajuste el montaje del canalAlmacenamiento fuera de temporada MantenimientoReposición del disyuntor LubricaciónReemplazo de la placa protectora ServicioReemplazo de la correa de la barrena Sujétela con los tres tornillos que extrajo anteriormenteReemplazo de las ruedas Reemplazo de la correa dienteProblema Causa Solución Solución de ProblemasEn Estados Unidos de América En Canadá Garantía Limitada DEL Fabricante Para