Craftsman C459-52833 To Engage Drive, To Engage Augers, Operating Tips, General Recommendations

Page 14

OPERATION

To Engage Drive

WARNING: The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear safety glasses while operating the snow thrower, or while performing any adjustments or repairs on it.

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.

WARNING: The temperature of the muffler and the surrounding areas may exceed 150° F (65° C). Avoid these areas.

1.If possible, remove snow immediately after it falls.

2.Discharge snow downwind whenever possible.

3.Slightly overlap each previous path.

4.Set the skid shoes 1/4” below the shave plate for normal usage. Adjust them upward for hard-packed snow and downward when using on gravel or crushed rock.

General Recommendations

1.Always observe safety rules when performing any maintenance.

2.The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the snow thrower as instructed here.

3.Some adjustments will have to be made periodically to maintain your unit properly.

4.Periodically check all fasteners and make sure these are tight.

Augers

WARNING: Always turn off the snowthrower’s engine and remove the key prior to replacing shear pins.

•The augers are secured to the spiral shaft with shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear. See Figure 13.

•If the augers will not turn, check to see if the pins have sheared.

One set of replacement shear pins has been provided with the snow thrower. When replacing pins, spray an oil lubricant into shaft before inserting new pins.

Figure 13

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual 200802488 Model Number Table of ContentsWarranty Statement Preparation Safety InstructionsTraining Safe Handling of GasolineDo not modify engine Maintenance & StorageOperation Average Useful LifeSafety Symbols Symbol DescriptionAssembly Attaching the Chute Assembly Attaching the Shift RodDrift Cutters Clean-Out ToolFinal Adjustments Skid ShoesAuger Control Operation Shift LeverTwo-Way Chute Control Chute Clean-Out ToolDrive Control / Auger Control Lock Chute Directional ControlElectric Starter Starting The EngineStopping The Engine Recoil StarterOperating Tips To Engage DriveTo Engage Augers General RecommendationsDrive Control AdjustmentsShift Rod Auger Control Chute AssemblyChute Bracket Adjustment Maintenance Auger Belt Drive Belt Changing Friction Wheel Rubber OFF-SEASON Storage Troubleshooting Page Parts LIST/PIÈCES Détachées Part RÉF Pièce Description Serrez à un couple Part RÉF Pièce Description Part RÉF Pièce Description Lead wire under fuel tank Contre le moteurDe 20-30 po-lb See chart on next page./ Voir le tableau à la page prochaîne Taille Logement Page Page Dépannage Neige laPrécédemment Saison Hors RemisageEntretien Frottement de Jusqu’à moteur le tourner Laissez AvertissementCôté chaque Poulie la démontantFente AdaptateurTarière la de d’entraînement Courroie Lubrification FondRéglages ’utilisation Roues des l’entraînement de CommandeVitesses de levier du Tige ’utilisation Conseils Général d’ordre RecommandationsUtilisation Tarières les embrayer PourMoteur du Arrêt Moteur le démarrer faire PourContact de Clé Roues des d’orientation CommandeFonctions 2 à goulotte la de Commande Roues des Sécurité votre compromettre et tarière Tarière la de CommandeMontage Le excessivement pas serrez Ne AvertissementGoulotte la de Réglages Derniers essayezet déplacerdeCoupe de Barres DégagementVitesses de levier du tige la de Installation Goulotte la de Installation’assemblage Avant Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage pour requis ArticlesSécurité DE Symboles Description SymboleMoyenne utile vie de Durée Sécurité DE Consignes ImportantEmisage Entretien Et R Utilisation Gaz de émissions les concernant AvisPréparation FormationMatières DES Table Modèle DE NuméroGarantie Dessus-ci d’achat6665-361-800-1 Impoà’utilisation Notice

C459-52833 specifications

The Craftsman C459-52833 is a versatile and powerful tool that caters to the needs of both professionals and hobbyists. This tool is designed with a variety of features that enhance its usability and performance, making it an essential addition to any workshop or garage.

One of the standout features of the Craftsman C459-52833 is its robust construction. Built from high-quality materials, it ensures durability and longevity, allowing users to tackle a wide range of projects without worrying about wear and tear. The ergonomic design is another significant aspect, offering a comfortable grip that minimizes fatigue during extended use. This is particularly important for those engaging in lengthy crafting sessions or demanding tasks.

Another key characteristic of the Craftsman C459-52833 is its impressive power output. Equipped with a high-torque motor, it delivers optimal performance for various applications. This power allows users to handle tough materials easily, whether it’s wood, metal, or plastic. The adjustable speed settings further enhance its versatility, enabling users to select the appropriate speed for each specific task, thus achieving precise results.

The Craftsman C459-52833 also incorporates advanced technologies that improve its performance and ease of use. For example, it features a user-friendly interface that provides clear indicators and controls, making it accessible for beginners and experts alike. The integrated safety features, such as overload protection and an automatic shut-off mechanism, ensure safe operation, reducing the risk of accidents during usage.

In terms of versatility, the Craftsman C459-52833 supports a wide range of attachments and accessories, allowing users to customize their experience further. This adaptability makes it suitable for various applications, from detailed craftwork to heavy-duty repairs.

Furthermore, the portability of the Craftsman C459-52833 adds to its appeal. Its lightweight design and compact size make it easy to transport, enabling users to bring it to job sites or different areas of their workspace without hassle.

In summary, the Craftsman C459-52833 stands out with its robust construction, powerful motor, adjustable speed settings, and safety features. Ideal for both professionals and DIY enthusiasts, this tool combines performance, versatility, and ease of use, making it an invaluable asset in any toolkit. Whether you’re embarking on a large project or tackling everyday repairs, the Craftsman C459-52833 is poised to deliver the results you need with efficiency and reliability.
Top Page Image Contents