Craftsman C459-52833 manual Auger Control, Chute Assembly, Chute Bracket Adjustment

Page 16

ADJUSTMENTS

Friction

Wheel

Drive

Axle

Support

Plate

Bracket

 

 

Opening

Figure 16

Skid Shoes

IMPORTANT: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position.

See Figure 17.

Adjust skid shoes as follows:

1.Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

2.Raise or lower the skid shoe to desired position.

3.Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear.

4. Repeat on the other side of the snow thrower.

Auger Control

Refer to instructions on page 9 to adjust the auger control. Make certain to check for correct adjustment as instructed before operating the snow thrower.

Figure 17

Figure 18

Chute Assembly

The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to Assembly section of this manual.

The remote chute control cables have been pre-adjusted at the factory. Move the remote chute lever on the control panel back and forward to adjust angle of the chute assembly.

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, the chute bracket can be adjusted. To do so:

1.Loosen the two nuts which secure the chute bracket and reposition it slightly. See Figure 18.

2.Retighten the nuts.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s Manual 200802488 Warranty Statement Table of ContentsModel Number Safety Instructions TrainingPreparation Safe Handling of GasolineMaintenance & Storage OperationDo not modify engine Average Useful LifeSafety Symbols Symbol DescriptionAssembly Attaching the Chute Assembly Attaching the Shift RodClean-Out Tool Final AdjustmentsDrift Cutters Skid ShoesAuger Control Operation Shift LeverChute Clean-Out Tool Drive Control / Auger Control LockTwo-Way Chute Control Chute Directional ControlStarting The Engine Stopping The EngineElectric Starter Recoil StarterTo Engage Drive To Engage AugersOperating Tips General RecommendationsShift Rod AdjustmentsDrive Control Chute Bracket Adjustment Chute AssemblyAuger Control Maintenance Auger Belt Drive Belt Changing Friction Wheel Rubber OFF-SEASON Storage Troubleshooting Page Parts LIST/PIÈCES Détachées Part RÉF Pièce Description Serrez à un couple Part RÉF Pièce Description Part RÉF Pièce Description Lead wire under fuel tank Contre le moteurDe 20-30 po-lb See chart on next page./ Voir le tableau à la page prochaîne Taille Logement Page Page Dépannage Neige laEntretien Saison Hors RemisagePrécédemment Frottement de Jusqu’à moteur le tourner Laissez AvertissementPoulie la démontant FenteCôté chaque AdaptateurTarière la de d’entraînement Courroie Lubrification FondRéglages Vitesses de levier du Tige Roues des l’entraînement de Commande’utilisation Général d’ordre Recommandations Utilisation’utilisation Conseils Tarières les embrayer PourMoteur du Arrêt Moteur le démarrer faire PourFonctions 2 à goulotte la de Commande Roues des d’orientation CommandeContact de Clé Roues des Tarière la de Commande MontageSécurité votre compromettre et tarière Le excessivement pas serrez Ne AvertissementRéglages Derniers essayezet déplacerde Coupe de BarresGoulotte la de DégagementVitesses de levier du tige la de Installation Goulotte la de InstallationGoulotte la de manivelle la de Montage Guidon du Montage’assemblage Avant ’assemblage pour requis ArticlesSécurité DE Symboles Description SymboleSécurité DE Consignes Important Emisage Entretien Et R UtilisationMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation FormationModèle DE Numéro GarantieMatières DES Table Dessus-ci d’achat6665-361-800-1 Impoà’utilisation Notice

C459-52833 specifications

The Craftsman C459-52833 is a versatile and powerful tool that caters to the needs of both professionals and hobbyists. This tool is designed with a variety of features that enhance its usability and performance, making it an essential addition to any workshop or garage.

One of the standout features of the Craftsman C459-52833 is its robust construction. Built from high-quality materials, it ensures durability and longevity, allowing users to tackle a wide range of projects without worrying about wear and tear. The ergonomic design is another significant aspect, offering a comfortable grip that minimizes fatigue during extended use. This is particularly important for those engaging in lengthy crafting sessions or demanding tasks.

Another key characteristic of the Craftsman C459-52833 is its impressive power output. Equipped with a high-torque motor, it delivers optimal performance for various applications. This power allows users to handle tough materials easily, whether it’s wood, metal, or plastic. The adjustable speed settings further enhance its versatility, enabling users to select the appropriate speed for each specific task, thus achieving precise results.

The Craftsman C459-52833 also incorporates advanced technologies that improve its performance and ease of use. For example, it features a user-friendly interface that provides clear indicators and controls, making it accessible for beginners and experts alike. The integrated safety features, such as overload protection and an automatic shut-off mechanism, ensure safe operation, reducing the risk of accidents during usage.

In terms of versatility, the Craftsman C459-52833 supports a wide range of attachments and accessories, allowing users to customize their experience further. This adaptability makes it suitable for various applications, from detailed craftwork to heavy-duty repairs.

Furthermore, the portability of the Craftsman C459-52833 adds to its appeal. Its lightweight design and compact size make it easy to transport, enabling users to bring it to job sites or different areas of their workspace without hassle.

In summary, the Craftsman C459-52833 stands out with its robust construction, powerful motor, adjustable speed settings, and safety features. Ideal for both professionals and DIY enthusiasts, this tool combines performance, versatility, and ease of use, making it an invaluable asset in any toolkit. Whether you’re embarking on a large project or tackling everyday repairs, the Craftsman C459-52833 is poised to deliver the results you need with efficiency and reliability.
Top Page Image Contents