Craftsman C459-52833 manual Drive Control / Auger Control Lock, Two-Way Chute Control, Skid Shoes

Page 12

OPERATION

Auger Control

The auger control is located on the left handle. Squeeze the auger control to engage the augers. Release to stop the snow throwing action. The drive control must also be released in order to stop auger

!5'%2

#/.42/,

#(54%5$)2%#4)/.!,2#/.42/,

$)3#(!2'%

$)3#(!2'%

,%&4

2)'(4

#(54%54),4 $/7.

#(54%54),4

50

'/

Drive Control / Auger Control Lock

The drive control is located on the right handle. Squeeze the drive control to engage the wheel drive. Release to stop.

This same lever also locks the auger control so you can operate the chute crank without interrupting the snow throwing process. If the auger control is engaged simultaneously with the drive control, the operator can release the auger control (on the left handle) and the augers will remain engaged. Release the drive control to stop the augers and wheel drive (the auger control must also be released).

IMPORTANT: NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system.

$2)6%

#/.42/,

'/

Two-Way Chute Control™)

This two-way control lever is meant to control the distance of snow discharge from the chute. Tilt the lever forward or rearward to adjust the distance snow will be thrown.

Chute Directional Control

The chute directional control is located on left side of the snow thrower. To change the direction in which snow is thrown, turn chute directional control as follows:

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

Wheel Steering Controls

The left and right wheel steering controls are located on the underside of the handles. Squeeze the right control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until you are familiar with these controls.

Chute Clean-Out Tool

WARNING: Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

The clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip.

1.Release both the auger control and the drive/auger control lock.

2.Stop the engine by moving the throttle to the stop position.

3.Remove the clean-out tool from the mounting clip.

4.Use the shovel-shaped end of the clean-out tool to remove any snow and ice in the chute assembly.

5.Re-fasten the clean-out tool to the mounting clip on the rear of the auger housing and restart engine.

6.While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow or ice from the chute assembly before continuing to clear snow.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Headlight

The headlight is on whenever the engine is running.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual 200802488 Table of Contents Warranty StatementModel Number Safety Instructions TrainingPreparation Safe Handling of GasolineMaintenance & Storage OperationDo not modify engine Average Useful LifeSafety Symbols Symbol DescriptionAssembly Attaching the Chute Assembly Attaching the Shift RodClean-Out Tool Final AdjustmentsDrift Cutters Skid ShoesAuger Control Operation Shift LeverChute Clean-Out Tool Drive Control / Auger Control LockTwo-Way Chute Control Chute Directional ControlStarting The Engine Stopping The EngineElectric Starter Recoil StarterTo Engage Drive To Engage AugersOperating Tips General RecommendationsAdjustments Shift RodDrive Control Chute Assembly Chute Bracket AdjustmentAuger Control Maintenance Auger Belt Drive Belt Changing Friction Wheel Rubber OFF-SEASON Storage Troubleshooting Page Parts LIST/PIÈCES Détachées Part RÉF Pièce Description Serrez à un couple Part RÉF Pièce Description Part RÉF Pièce Description Lead wire under fuel tank Contre le moteurDe 20-30 po-lb See chart on next page./ Voir le tableau à la page prochaîne Taille Logement Page Page Dépannage Neige laSaison Hors Remisage EntretienPrécédemment Frottement de Jusqu’à moteur le tourner Laissez AvertissementPoulie la démontant FenteCôté chaque AdaptateurTarière la de d’entraînement Courroie Lubrification FondRéglages Roues des l’entraînement de Commande Vitesses de levier du Tige’utilisation Général d’ordre Recommandations Utilisation’utilisation Conseils Tarières les embrayer PourMoteur du Arrêt Moteur le démarrer faire PourRoues des d’orientation Commande Fonctions 2 à goulotte la de CommandeContact de Clé Roues des Tarière la de Commande MontageSécurité votre compromettre et tarière Le excessivement pas serrez Ne AvertissementRéglages Derniers essayezet déplacerde Coupe de BarresGoulotte la de DégagementVitesses de levier du tige la de Installation Goulotte la de InstallationGoulotte la de manivelle la de Montage Guidon du Montage’assemblage Avant ’assemblage pour requis ArticlesSécurité DE Symboles Description SymboleSécurité DE Consignes Important Emisage Entretien Et R UtilisationMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation FormationModèle DE Numéro GarantieMatières DES Table Dessus-ci d’achat6665-361-800-1 Impoà’utilisation Notice

C459-52833 specifications

The Craftsman C459-52833 is a versatile and powerful tool that caters to the needs of both professionals and hobbyists. This tool is designed with a variety of features that enhance its usability and performance, making it an essential addition to any workshop or garage.

One of the standout features of the Craftsman C459-52833 is its robust construction. Built from high-quality materials, it ensures durability and longevity, allowing users to tackle a wide range of projects without worrying about wear and tear. The ergonomic design is another significant aspect, offering a comfortable grip that minimizes fatigue during extended use. This is particularly important for those engaging in lengthy crafting sessions or demanding tasks.

Another key characteristic of the Craftsman C459-52833 is its impressive power output. Equipped with a high-torque motor, it delivers optimal performance for various applications. This power allows users to handle tough materials easily, whether it’s wood, metal, or plastic. The adjustable speed settings further enhance its versatility, enabling users to select the appropriate speed for each specific task, thus achieving precise results.

The Craftsman C459-52833 also incorporates advanced technologies that improve its performance and ease of use. For example, it features a user-friendly interface that provides clear indicators and controls, making it accessible for beginners and experts alike. The integrated safety features, such as overload protection and an automatic shut-off mechanism, ensure safe operation, reducing the risk of accidents during usage.

In terms of versatility, the Craftsman C459-52833 supports a wide range of attachments and accessories, allowing users to customize their experience further. This adaptability makes it suitable for various applications, from detailed craftwork to heavy-duty repairs.

Furthermore, the portability of the Craftsman C459-52833 adds to its appeal. Its lightweight design and compact size make it easy to transport, enabling users to bring it to job sites or different areas of their workspace without hassle.

In summary, the Craftsman C459-52833 stands out with its robust construction, powerful motor, adjustable speed settings, and safety features. Ideal for both professionals and DIY enthusiasts, this tool combines performance, versatility, and ease of use, making it an invaluable asset in any toolkit. Whether you’re embarking on a large project or tackling everyday repairs, the Craftsman C459-52833 is poised to deliver the results you need with efficiency and reliability.
Top Page Image Contents