Craftsman C459-52833 manual Drive Belt

Page 19

MAINTENANCE

Figure 27

Figure 28

NOTE: The pulley adapter may slide off the auger input shaft when remov- ing the pulley. Use extra caution to ensure the adapter does fall and/or get damaged when removing the pulley.

11.Place the new auger belt in the V-groove of the auger pulley and place the pulley w/belt inside the belt keepers.

12.Turn the pulley as necessary to align its three slots approximately with the posts of the pulley adapter, then move the brake bracket assembly away from the input shaft. While aligning the pulley slots and adapter posts, push the auger pulley fully onto the adapter. Refer to Figure 29.

NOTE: If the pulley adapter was removed with the pulley, align the splines of the pulley adapter and auger input shaft, and push the pulley and adapter onto the input shaft. Refer to Figure 29.

13.Slide the washer onto the hex screw removed earlier and apply Loctite 262 to the threads of the hex screw.

14.Insert the hex screw through the pulley assembly and into the threads of the input shaft. Torque the hex screw to 250-325 in./lbs. to secure the auger pulley assembly on the input shaft.

a

b Adapter

c

Slots

If also replacing the drive belt, proceed to the “Drive Belt” instruction. If not, reassemble by performing the previous steps in the opposite order and manner of removal.

NOTE: Make sure to remove the piece of wood blocking the impeller.

Proper Adjustment: With the auger clutch lever in the disengaged position, the top surface of the new belt should be even with the outside diameter of the pulley.

1.To adjust, disconnect ferrule from brake bracket assembly and thread ferrule in (towards idler) to increase tension on belt, and out to decrease tension.

NOTE: The brake puck must always be firmly seated in the pulley groove when auger control is disengaged.

IMPORTANT: Repeat the “Auger Drive Control Test” from the Assembly section before operating snow thrower.

Drive Belt

1.Pull the idler pulley away from the backside of the drive belt to relieve the tension and slide the drive belt off the idler pulley. See Figure 30.

Figure 29

3

1b

1a

2

Figure 30

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 2008 Operator’s Manual02488 Warranty Statement Table of ContentsModel Number Safe Handling of Gasoline Safety InstructionsTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSymbol Description Safety SymbolsAssembly Attaching the Shift Rod Attaching the Chute AssemblySkid Shoes Clean-Out ToolFinal Adjustments Drift CuttersAuger Control Shift Lever OperationChute Directional Control Chute Clean-Out ToolDrive Control / Auger Control Lock Two-Way Chute ControlRecoil Starter Starting The EngineStopping The Engine Electric StarterGeneral Recommendations To Engage DriveTo Engage Augers Operating TipsShift Rod AdjustmentsDrive Control Chute Bracket Adjustment Chute AssemblyAuger Control Maintenance Auger Belt Drive Belt Changing Friction Wheel Rubber OFF-SEASON Storage Troubleshooting Page Parts LIST/PIÈCES Détachées Part RÉF Pièce Description Serrez à un couple Part RÉF Pièce Description Part RÉF Pièce Description Contre le moteur Lead wire under fuel tankDe 20-30 po-lb See chart on next page./ Voir le tableau à la page prochaîne Taille Logement Page Page Neige la DépannageEntretien Saison Hors RemisagePrécédemment Jusqu’à moteur le tourner Laissez Avertissement Frottement deAdaptateur Poulie la démontantFente Côté chaqueTarière la de d’entraînement Courroie Fond LubrificationRéglages Vitesses de levier du Tige Roues des l’entraînement de Commande’utilisation Tarières les embrayer Pour Général d’ordre RecommandationsUtilisation ’utilisation ConseilsMoteur le démarrer faire Pour Moteur du ArrêtFonctions 2 à goulotte la de Commande Roues des d’orientation CommandeContact de Clé Roues des Le excessivement pas serrez Ne Avertissement Tarière la de CommandeMontage Sécurité votre compromettre et tarièreDégagement Réglages Derniers essayezet déplacerdeCoupe de Barres Goulotte la deGoulotte la de Installation Vitesses de levier du tige la de Installation’assemblage pour requis Articles Goulotte la de manivelle la de MontageGuidon du Montage ’assemblage AvantDescription Symbole Sécurité DE SymbolesGaz de émissions les concernant Avis Sécurité DE Consignes ImportantEmisage Entretien Et R Utilisation Moyenne utile vie de DuréeFormation PréparationDessus-ci d’achat Modèle DE NuméroGarantie Matières DES TableImpoà 6665-361-800-1’utilisation Notice

C459-52833 specifications

The Craftsman C459-52833 is a versatile and powerful tool that caters to the needs of both professionals and hobbyists. This tool is designed with a variety of features that enhance its usability and performance, making it an essential addition to any workshop or garage.

One of the standout features of the Craftsman C459-52833 is its robust construction. Built from high-quality materials, it ensures durability and longevity, allowing users to tackle a wide range of projects without worrying about wear and tear. The ergonomic design is another significant aspect, offering a comfortable grip that minimizes fatigue during extended use. This is particularly important for those engaging in lengthy crafting sessions or demanding tasks.

Another key characteristic of the Craftsman C459-52833 is its impressive power output. Equipped with a high-torque motor, it delivers optimal performance for various applications. This power allows users to handle tough materials easily, whether it’s wood, metal, or plastic. The adjustable speed settings further enhance its versatility, enabling users to select the appropriate speed for each specific task, thus achieving precise results.

The Craftsman C459-52833 also incorporates advanced technologies that improve its performance and ease of use. For example, it features a user-friendly interface that provides clear indicators and controls, making it accessible for beginners and experts alike. The integrated safety features, such as overload protection and an automatic shut-off mechanism, ensure safe operation, reducing the risk of accidents during usage.

In terms of versatility, the Craftsman C459-52833 supports a wide range of attachments and accessories, allowing users to customize their experience further. This adaptability makes it suitable for various applications, from detailed craftwork to heavy-duty repairs.

Furthermore, the portability of the Craftsman C459-52833 adds to its appeal. Its lightweight design and compact size make it easy to transport, enabling users to bring it to job sites or different areas of their workspace without hassle.

In summary, the Craftsman C459-52833 stands out with its robust construction, powerful motor, adjustable speed settings, and safety features. Ideal for both professionals and DIY enthusiasts, this tool combines performance, versatility, and ease of use, making it an invaluable asset in any toolkit. Whether you’re embarking on a large project or tackling everyday repairs, the Craftsman C459-52833 is poised to deliver the results you need with efficiency and reliability.
Top Page Image Contents