Craftsman C459-52833 Drift Cutters, Clean-Out Tool, Skid Shoes, Tire Pressure Pneumatic Tires

Page 9

ASSEMBLY

Drift Cutters

Drift cutters should be used when operating the snow thrower in heavy drift conditions.

•Remove the carriage bolts by unthreading the hex nuts which secure them, and reinstall the drift cutters facing forward before operating the snow thrower. Refer to Figure 7.

Figure 7

Clean-Out Tool

The clean-out tool is mounted to the rear of the auger housing and is designed to clear a clogged chute. See Figure 8. Refer to page 11 for instructions on how to properly use it.

NOTE: This item is fastened with a cable tie to the rear of the auger housing at the factory. Cut the cable tie before operating the snow thrower.

WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. See “Making Adjustment” Section.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check the tire pressure before operating the snow thrower. Refer to the tire side wall for tire manufacturer’s recommended psi and deflate (or inflate) the tires as necessary.

IMPORTANT: If the tire pressure is not equal in both tires, the unit may not travel in a straight path and the shave plate may wear unevenly.

Final Adjustments

Make these final adjustments before operating your snow thrower for the first time. Failure to follow these instructions may cause damage to the snow thrower.

Chute Clean-out Tool

Figure 8

 

Auger

Drive

Control

Control

Chute Tilt Control

 

Shift Lever

 

 

Drive

Auger

Control

Cable

Control

 

Cable

 

Figure 9

Wheel Drive Control & Shift Lever

Perform the following test to determine need for adjustment:

•Move the shift lever into sixth (6) position. See Figure 9.

•With the drive control released (see Figure 9), push the snow thrower forward, then pull it back. The machine should move freely.

•Engage the drive control and attempt to move the machine both forward and back, resistance should be felt.

•Move the shift lever into the fast reverse (R2) position and repeat the previous two steps.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 2008 Operator’s Manual02488 Table of Contents Warranty StatementModel Number Training Safety InstructionsPreparation Safe Handling of GasolineOperation Maintenance & StorageDo not modify engine Average Useful LifeSymbol Description Safety SymbolsAssembly Attaching the Shift Rod Attaching the Chute AssemblyFinal Adjustments Clean-Out ToolDrift Cutters Skid ShoesAuger Control Shift Lever OperationDrive Control / Auger Control Lock Chute Clean-Out ToolTwo-Way Chute Control Chute Directional ControlStopping The Engine Starting The EngineElectric Starter Recoil StarterTo Engage Augers To Engage DriveOperating Tips General RecommendationsAdjustments Shift RodDrive Control Chute Assembly Chute Bracket AdjustmentAuger Control Maintenance Auger Belt Drive Belt Changing Friction Wheel Rubber OFF-SEASON Storage Troubleshooting Page Parts LIST/PIÈCES Détachées Part RÉF Pièce Description Serrez à un couple Part RÉF Pièce Description Part RÉF Pièce Description Contre le moteur Lead wire under fuel tankDe 20-30 po-lb See chart on next page./ Voir le tableau à la page prochaîne Taille Logement Page Page Neige la DépannageSaison Hors Remisage EntretienPrécédemment Jusqu’à moteur le tourner Laissez Avertissement Frottement deFente Poulie la démontantCôté chaque AdaptateurTarière la de d’entraînement Courroie Fond LubrificationRéglages Roues des l’entraînement de Commande Vitesses de levier du Tige’utilisation Utilisation Général d’ordre Recommandations’utilisation Conseils Tarières les embrayer PourMoteur le démarrer faire Pour Moteur du ArrêtRoues des d’orientation Commande Fonctions 2 à goulotte la de CommandeContact de Clé Roues des Montage Tarière la de CommandeSécurité votre compromettre et tarière Le excessivement pas serrez Ne AvertissementCoupe de Barres Réglages Derniers essayezet déplacerdeGoulotte la de DégagementGoulotte la de Installation Vitesses de levier du tige la de InstallationGuidon du Montage Goulotte la de manivelle la de Montage’assemblage Avant ’assemblage pour requis ArticlesDescription Symbole Sécurité DE SymbolesEmisage Entretien Et R Utilisation Sécurité DE Consignes ImportantMoyenne utile vie de Durée Gaz de émissions les concernant AvisFormation PréparationGarantie Modèle DE NuméroMatières DES Table Dessus-ci d’achatImpoà 6665-361-800-1’utilisation Notice

C459-52833 specifications

The Craftsman C459-52833 is a versatile and powerful tool that caters to the needs of both professionals and hobbyists. This tool is designed with a variety of features that enhance its usability and performance, making it an essential addition to any workshop or garage.

One of the standout features of the Craftsman C459-52833 is its robust construction. Built from high-quality materials, it ensures durability and longevity, allowing users to tackle a wide range of projects without worrying about wear and tear. The ergonomic design is another significant aspect, offering a comfortable grip that minimizes fatigue during extended use. This is particularly important for those engaging in lengthy crafting sessions or demanding tasks.

Another key characteristic of the Craftsman C459-52833 is its impressive power output. Equipped with a high-torque motor, it delivers optimal performance for various applications. This power allows users to handle tough materials easily, whether it’s wood, metal, or plastic. The adjustable speed settings further enhance its versatility, enabling users to select the appropriate speed for each specific task, thus achieving precise results.

The Craftsman C459-52833 also incorporates advanced technologies that improve its performance and ease of use. For example, it features a user-friendly interface that provides clear indicators and controls, making it accessible for beginners and experts alike. The integrated safety features, such as overload protection and an automatic shut-off mechanism, ensure safe operation, reducing the risk of accidents during usage.

In terms of versatility, the Craftsman C459-52833 supports a wide range of attachments and accessories, allowing users to customize their experience further. This adaptability makes it suitable for various applications, from detailed craftwork to heavy-duty repairs.

Furthermore, the portability of the Craftsman C459-52833 adds to its appeal. Its lightweight design and compact size make it easy to transport, enabling users to bring it to job sites or different areas of their workspace without hassle.

In summary, the Craftsman C459-52833 stands out with its robust construction, powerful motor, adjustable speed settings, and safety features. Ideal for both professionals and DIY enthusiasts, this tool combines performance, versatility, and ease of use, making it an invaluable asset in any toolkit. Whether you’re embarking on a large project or tackling everyday repairs, the Craftsman C459-52833 is poised to deliver the results you need with efficiency and reliability.
Top Page Image Contents