Husqvarna 15530SB-LS Maintenance, General Recommendations, Before Each Use, Lubrication, Tires

Page 14
MAINTENANCE

MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower.

At least once a season, check to see if you should make any of the adjustments described in the Service and Ad- justments section of this manual.

•At least once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRICATION CHART”).

➀SAE 30 Motor Oil

➁ See “ENGINE” in

Maintenance section

➂ General

Purpose

Grease

➀ Pivot points

➂Auger grease fittings

➁Engine oil

SNOW THROWER

Always observe the safety rules when performing any maintenance.

TIRES

•Maintain proper air pressure in both tires (14–17 P.S.I. / 19-24.5 N-m).

•Keep tires free of gasoline and oil, which can harm rubber.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 15530SB-LS Operators ManualPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationClearing a Clogged Discharge Chute TABLE OF CONTENTSMaintenance and Storage PRODUCT SPECIFICATIONSPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSTraction drive control lever - used to engage power Recoil auxiliary starter handle - used for starting theTO USE FUEL SHUT-OFF VALVE See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE THROTTLE CONTROL See FigTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See FigSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig TO USE DRIFT CUTTERS See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENBEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONBELTS CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key CHUTE DEFLECTORTO REPLACE BELTS See Fig CARBURETOR TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles orSERVICE NOTES SERVICE NOTES SERVICE NOTES SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY
Top Page Image Contents