Husqvarna 15530SB-LS manual Service And Adjustments, Engine, TO REMOVE WHEELS See Fig, Carburetor

Page 18

TO REMOVE WHEELS (See Fig. 25)

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 25)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL

WHEEL HUB

FIG. 25

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO ADJUST CABLE TENSION (See Fig. 26)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 26

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

18

Image 18

Contents 15530SB-LS Operators ManualPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationClearing a Clogged Discharge Chute TABLE OF CONTENTSMaintenance and Storage PRODUCT SPECIFICATIONSPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andUNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSTraction drive control lever - used to engage power Recoil auxiliary starter handle - used for starting theTO USE FUEL SHUT-OFF VALVE See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE THROTTLE CONTROL See FigTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See FigSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig TO USE DRIFT CUTTERS See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENBEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONBELTS CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key CHUTE DEFLECTORTO REPLACE BELTS See Fig CARBURETOR TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles orSERVICE NOTES SERVICE NOTES SERVICE NOTES SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY