Husqvarna 15530SB-LS manual Operation, Meets A.N.S.I. Safety Requirements

Page 9
MEETS A.N.S.I. SAFETY REQUIREMENTS

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE Drive speed control lever - used to select forward or CON-

ELECTRIC

 

DISCHARGE CHUTE CONTROL LEVER

START

AUGER

 

DEFLECTOR

TRACTION

BUTTON

 

DRIVE

RECOIL

CONTROL

DRIVE SPEED

REMOTE

CONTROL

LEVER

CONTROL

CONTROL LEVER

LEVER

(AUXILIARY)

 

LEVER

 

 

 

STARTER

 

 

 

 

HANDLE

 

 

 

 

 

CHUTE

 

 

 

DEFLECTOR

 

 

 

TROL

PRIMER

SAFETY IGNITION KEY

FUEL SHUT-OFF

VALVE THROTTLE / ENGINE CONTROL

LH TURN

TRIGGER

DISCHARGE

CHUTE

CLEAN-OUT TOOL

LIGHT

HANDLE KNOB

MUFFLER

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

FIG. 10

TOOLBOX

DRIFT

CUTTER

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and

Drive speed control lever - used to select forward or

wrench.

reverse motion and speed of snow thrower.

Safety ignition key - must be inserted for the engine to

Traction drive control lever - used to engage power-

start and run. Remove when snow thrower is not in use.

propelled forward or reverse motion of snow thrower.

Electric start button – used for starting the engine.

LH and RH turn triggers - used to steer the snow thrower.

Recoil (auxiliary) starter handle – used for starting the

Auger control lever - used to engage auger motion (throw

engine.

snow).

Primer - pumps additional fuel from the carburetor to the

Discharge chute control lever - used to change the di-

cylinder for use when starting a cold engine.

rection the snow is thrown.

Throttle/engine control - used to select either FAST or

Skid plate - used to adjust height of scraper bar from the

SLOW engine speed and to STOP the engine.

ground.

Choke control - used for starting a cold engine.

9 Drift cutter - used to cut through deep snowdrifts.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operators Manual 15530SB-LSTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationMaintenance and Storage TABLE OF CONTENTSClearing a Clogged Discharge Chute PRODUCT SPECIFICATIONSHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andKNOW YOUR SNOW THROWER OPERATIONTraction drive control lever - used to engage power MEETS A.N.S.I. SAFETY REQUIREMENTSDrive speed control lever - used to select forward or Recoil auxiliary starter handle - used for starting theSTOPPING HOW TO USE YOUR SNOW THROWERTO USE FUEL SHUT-OFF VALVE See Fig TO USE THROTTLE CONTROL See FigPOWER STEERING OPERATION See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig TO USE DRIFT CUTTERS See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGBELTS AUGER GEAR CASE1. Be sure throttle is in STOP position 2. Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orSERVICE NOTES SERVICE NOTES SERVICE NOTES SECTION 1 LIMITED WARRANTY WARRANTY STATEMENTSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY
Top Page Image Contents