Husqvarna 15530SB-LS manual Assembly / Pre-Operation, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
		BETWEEN
		HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

Image 7

Contents Operators Manual 15530SB-LSOperation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationPRODUCT SPECIFICATIONS TABLE OF CONTENTSMaintenance and Storage Clearing a Clogged Discharge ChuteREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER PARTS PACKED SEPARATELY IN CARTONINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL SPEED CONTROL ROD See Figs. 1 andUNFOLD UPPER HANDLE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andKNOW YOUR SNOW THROWER OPERATIONRecoil auxiliary starter handle - used for starting the MEETS A.N.S.I. SAFETY REQUIREMENTSTraction drive control lever - used to engage power Drive speed control lever - used to select forward orTO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO THROW SNOW See FigTO USE DRIFT CUTTERS See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR See FigIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSTO START ENGINE BEFORE STOPPINGLUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE BELTSCHUTE DEFLECTOR SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig ENGINE SPEED TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig CARBURETORENGINE OIL STORAGEOTHER FUEL SYSTEMEngine idles or TROUBLESHOOTINGLoss of power Does not startSERVICE NOTES SERVICE NOTES SERVICE NOTES SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY