Husqvarna 15530SB-LS manual Assembly / Pre-Operation, INSTALL AUGER CONTROL ROD See Figs. 5 and

Page 6

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotate chute assembly to alignsquare andpin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATER		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATER HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

6

Image 6

Contents 15530SB-LS Operators ManualPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationClearing a Clogged Discharge Chute TABLE OF CONTENTSMaintenance and Storage PRODUCT SPECIFICATIONSPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andUNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERDrive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTSTraction drive control lever - used to engage power Recoil auxiliary starter handle - used for starting theTO USE FUEL SHUT-OFF VALVE See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE THROTTLE CONTROL See FigTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See FigSCRAPER BAR See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig TO USE DRIFT CUTTERS See FigBEFORE STOPPING SNOW THROWING TIPSTO START ENGINE IF RECOIL STARTER HAS FROZENBEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONBELTS CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key CHUTE DEFLECTORTO REPLACE BELTS See Fig CARBURETOR TO ADJUST CABLE TENSION See FigTO REMOVE WHEELS See Fig ENGINE SPEEDFUEL SYSTEM STORAGEOTHER ENGINE OILDoes not start TROUBLESHOOTINGLoss of power Engine idles orSERVICE NOTES SERVICE NOTES SERVICE NOTES SECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY