Husqvarna 15530SB-LS manual Assembly / Pre-Operation, Unfold Upper Handle

Page 5

UNFOLD UPPER HANDLE

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

FIG. 2

5

Image 5

Contents Operators Manual 15530SB-LSTraining Safe Operation Practices for Walk-Behind Snow ThrowersPreparation OperationMaintenance and Storage TABLE OF CONTENTSClearing a Clogged Discharge Chute PRODUCT SPECIFICATIONSHOW TO SET UP YOUR SNOW THROWER ASSEMBLY / PRE-OPERATIONPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONUNFOLD UPPER HANDLE INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andCHECK TIRE PRESSURE INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andKNOW YOUR SNOW THROWER OPERATIONTraction drive control lever - used to engage power MEETS A.N.S.I. SAFETY REQUIREMENTSDrive speed control lever - used to select forward or Recoil auxiliary starter handle - used for starting theSTOPPING HOW TO USE YOUR SNOW THROWERTO USE FUEL SHUT-OFF VALVE See Fig TO USE THROTTLE CONTROL See FigPOWER STEERING OPERATION See Fig USING THE CLEAN-OUT TOOL See FigTO THROW SNOW See Fig TO MOVE FORWARD AND BACKWARD See FigTO ADJUST SKID PLATES See Fig BEFORE STARTING THE ENGINESCRAPER BAR See Fig TO USE DRIFT CUTTERS See FigTO START ENGINE SNOW THROWING TIPSBEFORE STOPPING IF RECOIL STARTER HAS FROZENGENERAL RECOMMENDATIONS MAINTENANCEBEFORE EACH USE LUBRICATIONENGINE CLEANINGBELTS AUGER GEAR CASE1. Be sure throttle is in STOP position 2. Remove safety ignition key SERVICE AND ADJUSTMENTSTO ADJUST SNOW THROWER HEIGHT CHUTE DEFLECTORTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig TO ADJUST CABLE TENSION See FigCARBURETOR ENGINE SPEEDOTHER STORAGEFUEL SYSTEM ENGINE OILLoss of power TROUBLESHOOTINGDoes not start Engine idles orSERVICE NOTES SERVICE NOTES SERVICE NOTES SECTION 1 LIMITED WARRANTY WARRANTY STATEMENTSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 3 ITEMS NOT COVERED BY THIS WARRANTY