Husqvarna 1130SB-LSB owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1. Read, understand and follow all instructions on the

 

(f) Keep the nozzle in contact with the rim of the fuel

machine and in the manual(s) before operating this

 

tank or container opening at all times, until refuel-

unit. Be thoroughly familiar with the controls and the

 

ing is complete. Do not use a nozzle lock-open

proper use of the equipment. Know how to stop the

 

device.

unit and disengage the controls quickly.

 

(g) Replace gasoline cap securely and wipe up spilled

2. Never allow children to operate the equipment. Never

 

fuel.

allow adults to operate the equipment without proper

 

(h) If fuel is spilled on clothing, change clothing im-

instruction.

 

 

mediately.

3. Keep the area of operation clear of all persons, par-

 

5. Use extension cords and receptacles as specified by

ticularly small children.

 

the manufacturer for all units with electric drive motors

 

 

 

4. Exercise caution to avoid slipping or falling, especially

 

or electric starting motors.

when operating the snow thrower in reverse.

6. Adjust the collector housing height to clear gravel or

Preparation

 

crushed rock surface.

7. Never attempt to make any adjustments while the

1. Thoroughly inspect the area where the equipment is

 

engine (motor) is running (except when specifically

to be used and remove all doormats, sleds, boards,

 

recommended by manufacturer).

wires, and other foreign objects.

8. Always wear safety glasses or eye shields during op-

2. Disengage all clutches and shift into neutral before

 

eration or while performing an adjustment or repair to

starting the engine (motor).

 

protect eyes from foreign objects that may be thrown

3. Do not operate the equipment without wearing adequate

 

from the machine.

winter garments. Avoid loose fitting clothing that can

Operation

get caught in moving parts. Wear footwear that will

improve footing on slippery surfaces.

1. Do not put hands or feet near or under rotating parts.

4. Handle fuel with care; it is highly flammable

 

Keep clear of the discharge opening at all times.

(a)

Use an approved fuel container.

2. Exercise extreme caution when operating on or cross-

(b)

Never add fuel to a running engine or hot en-

 

ing gravel drives, walks, or roads. Stay alert for hidden

 

hazards or traffic.

 

gine.

 

 

3.

After striking a foreign object, stop the engine (motor),

(c) Fill fuel tank outdoors with extreme care. Never fill

 

remove the wire from the spark plug, disconnect the

 

fuel tank indoors.

 

 

 

cord on electric motors, thoroughly inspect the snow

(d) Never fill containers inside a vehicle or on a truck

 

 

thrower for any damage, and repair the damage before

 

or trailer bed with a plastic liner. Always place

 

restarting and operating the snow thrower.

 

containers on the ground, away from your vehicle,

4. If the unit should start to vibrate abnormally, stop the

 

before filling.

 

 

engine (motor) and check immediately for the cause.

(e)

When practical, remove gas-powered equipment

 

 

Vibration is generally a warning of trouble.

 

from the truck or trailer and refuel it on the ground.

5.

Stop the engine (motor) whenever you leave the oper-

 

If this is not possible, then refuel such equipment

on a trailer with a portable container, rather than

 

ating position, before unclogging the collector/impeller

 

housing or discharge chute, and when making any

from a gasoline dispenser nozzle.

 

2

repairs, adjustments or inspections.

 

 

 

Image 2
Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 Lower Tube Gray Pivot Support532 18 77-16 Shifter ROD Bottom 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Clutch ROD532 17 86-66 Halogen Headlight Grip Switch532 42 14-48 Headlight Bezel Gray BulbDrive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX ShaftClevis PIN Assembly532 18 00-82 Intermediate Gear 532 17 53-44 Trunnion BearingGear Axle ShaftRoll PIN 3/16 Clik PINClutch Slide CoverWheel Lobe Axle LobeBottom PAN Chassis / Engine / PulleysFrame Engine Mount PlatePulley Impeller BeltWheels 532 19 30-71 Safety Ignition KEY Repair PartsPower Cord Retainer PIN532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement