Husqvarna 1130SB-LSB Chassis / Engine / Pulleys, Frame, Bottom PAN, Engine Mount Plate

Page 37

REPAIR PARTS

CHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

3

5 4

1

6

2

5

4

6

01.00.016-B

KEY

PART

DESCRIPTION

NO.

NO.

-- - - - - - - - - ENGINE B&S MODEL 21P214-1181-E1

1

532 41 53-40

FRAME

2

532 41 08-77

BOTTOM PAN

3

532 42 38-70

ENGINE MOUNT PLATE

4

532 15 04-06

BOLT 3/8−16

5817 00 05-12 SCREW 5/16−18 X .750

6532 18 44-71 SCREW 10−24 X .625

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A Knob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 Pivot Support Lower Tube Gray532 40 57-40 Traction ROD Assembly 532 18 04-80 Impeller ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch ROD532 42 14-48 Headlight Bezel Gray Grip Switch532 17 86-66 Halogen Headlight BulbDrive Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment HEX Shaft532 18 00-82 Intermediate Gear AssemblyClevis PIN 532 17 53-44 Trunnion BearingRoll PIN 3/16 Axle ShaftGear Clik PINWheel Lobe CoverClutch Slide Axle LobeFrame Chassis / Engine / PulleysBottom PAN Engine Mount PlateImpeller Belt PulleyWheels Power Cord Repair Parts532 19 30-71 Safety Ignition KEY Retainer PINDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement
Top Page Image Contents